Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I am a beginner trying to implement ble_app_uart example from SDK 15, example compiles with no problem, advertizes. LED 1 blinks when advertizing, and turns ON when connecting...
WHY WHY WHY!
You guys proudly release an upgrade to the programming tool within NRF Connect.
Then when a dummy like me upgrades I'm told that it's only supported by NRF...
Hi all,
I am working with SDK Thread V3.1.
I run simple_coap_server and simple_coap_client.It run normal.
Now, I want to add DTLS for this example for secure data. ...
As far as I understood, the flash protection can be realized by writing the 0x00 to the lowest 8 bits of UICR APPPROTECT register either putting it code image or via the nrfjprog...
Hello,
I use NRF52810 with SDK 14.2.0 and softdevice 112. I need to use 7 input pins, but if I config more than 3 pins, all signals disappear.
GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Hello all,
SDK:S332 V4.0.5(related to BLE V4.2).
Platform:NRF52832.
For improving BLE data throughout, i tried to set some configurations by other guidance.
Following...
Hi Tech Team,
I am using nRF52832 chip and the recent soft device(SD). I want to implement my own file storage and thus using sd_flash_write () and sd_flash_page_erase functionalities...
Hello Nordic experts,
I am using nRF52840 and SDK 15.3.0. I have added an OUT ENDPOINT to the usbd_hid_generic example by following the suggestions in https://devzone...
Hi,
I'm new to programming and I can't seem to solve this error of "No such file or directory" even when I already put the file in the location of the directory.
How...
I am writing a 1-wire driver (there doesn't appear to be one in the SDK), and am looking at dynamically switching the GPIO between read/write. There appears to be two functions...
I am running the light_switch example and it works fine works fine , I am using the nrf_application to configure the nodes.
I am using latest mesh sdk and 15.3 nrf sdk....
Hi guys
I had to integrate a CLI module into a project I'm working on, that is running FreeRTOS
after quite a lot of work, I managed to get this working, but seeing...
HI,
I am using nrf52832 dk. I have a sensor that gives a negative voltage. I want to measure the value using saadc.
and can I use differential mode saadc for negative...
Hello All,
I am working on the N51822 custom board.
Using segger IDE, SDK 12.3
Previously i have worked on the sdk 14.3 on the n52810 board. It is working properly...
