Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hello All I am new to this nordic semiconductors. I need information regarding nRF52840 DK boards.
* How to connect two nrF52840 DK(transmitter to receiver) and start advertising...
Hi, I have a SIM800L GSM/GPRS module that I can successfully talk to via the UART on the nRF51.
I can tell it to dial numbers etc and that all works fine.
My problem...
Hi, I'm using app_pwm with 32.768Khz external xtal. the following is my setting in sdk_config.h.
// <0=> RC // <1=> XTAL // <2=> Synth
#ifndef CLOCK_CONFIG_LF_SRC #define...
Hi,
I used sdk 15.2.0 version, I refer to the ATT_MTU Throughput Example to modify the Nordic UART Service (NUS) Application example.
Now I have some questions:
1. How...
Hello,
I'm using nRF52832, SDK15.0.0, Softdevice S132.
What should be the code added to application in order to support BLE DFU service?
I've been here , but its for...
hello,
I want to use RSSI on nrf52832, and the project is uploaded.
the question is, I test the RSSI on channel 2468MHZ， the NRF_RADIO->RSSISAMPLE result is about -92dBm...
Hi,
I followed the instructions for Getting Started with the NRF9160, activating the iBasis SIM card, placing into the board and applying USB power.
The first issue...
Hi,
I'm trying to update the firmware on my nRF9160 development kit
I downloaded the modem firmware and DFU tool
And then tried to follow these instructions: ...
Hi,
I want to activate eDRX on mqtt_simple example and measure the current consumption. I guess based on the code, by enabling "CONFIG_LTE_EDRX_REQ" it will be activated...
Hi guys,
I know that there is no official support for C++ on NordicSemi side, but I just wonder if it would be possible to work with C++ in Segger IDE. I'm trying to integrate...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi All,
I use ble_app_blinky example and Android nRF Blinky SDK to add new function.
Recently...
Hello,
I'm using NRF52840 module to make a customer device. This device send message by UART. My device is powered with a battery, for this reason I would like reduce the...
Hi All,
We are using NRF52832 in our project. We have implemented the c code to perform nrfutil operations.
We are following below steps to do it.
Erase all files...
Hi, I'm doing some tests with Legacy OOB and I made it work with Master Control Panel 3.10.0.14, but when I try with nRF Connect v2.6.2 it fails. I know MCP is not supported...
Hi nordic,
Please inform bjorn-spockeli to reply in this thread its very urgent
https://devzone.nordicsemi.com/f/nordic-q-a/45470/encryption-and-decryption-of-advertising...
