Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
I'm compiling my project successfully in Eclipse, but trying to build it from the command line (cygwin) fails near the end with this error (make, make all, make nrf51422_xxac_s110...
I want to restart the radio portion of the softdevice - all of BLE essentially - to update the connection parameters and device name mostly. Is it necessary to re-initialize...
Hello Everyone
I have designed the schematics for my prototype but i have a question for impedance matching can anyone verify my technical doubt
I had put a 2.45GHz...
We are using nrf51822 for products of our company. We use mbed + nRF51822 driver + BLE_API for the BLE peripheral devices. The softdevice is s130 ver 1.0.0.
I create an...
Can the nRF51X22 be paired with an iPhone to communicate (both ways) using regular BLE and emit a beacon signal at the same time? In fact, I'm looking to change the beacon...
So I suspect there is a very simple answer to this, but a couple days of much reading and searching haven't led me to a very clear answer.
My setup: Galaxy S3 (Android...
I'm trying to move data over the uart characteristic. I followed the guidelines here devzone.nordicsemi.com/.../
In the main loop I am calling sd_ble_gatts_hvx until it...
I'm working with an nrf51822 with the s110 softdevice. So I'm trying to read an analog signal from multiple pins. My program will run fine for quite some time. Eventually...
Hey guys,
I need to record many time interval ?, can i generate system time and use it to record all of my time intervals?
If I want to send all of the time intervals...
The gcc compiler is gcc-arm-none-eabi-4_9-2015q2.
The make version is GNU Make 4.0 (Build for arm-unknown-linux-gnueabihf).
The error message is:
... arm-none-eabi...
So I'm using the spi_master.c from SDK 6.1 to communicate with an LCD driver. I'm using an nrf51822 with s110 softdevice. My system has been sporadically hardfaulting on me...
Hello all,
I have found closed topics here with similar names ( devzone.nordicsemi.com/.../ etc.) but my question is about adding the characteristic with encryption.
My...
Hi,
I'm trying to transition my application from SDK 7.2.0 to SDK_9.0.0 and am having some issues when including ble_advdata.h compiling with gcc:
In file included from...
Hello,
I know I'm not supposed to use TIMER1 with IRQ 0 when using a SoftDevice but I want to try anyway :) I want to do some bit banging with timing that is timing sensitive...
I am trying to program custom boards with the NRF51822 using an ARM-Flasher with no success. Using J-Flash I can connect to the device properly, program and verify the hex...
