We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi!
I use SDK15.0 and s132_nrf52_6.0.0_softdevice
I use nRF52 in two modes- peripherial and central in one time.
When I use it like peripherial and have connect with...
I am using RTT to debug my application and it's fine when it's working. The problem is that it seems to be flaky as hell. Sometimes it just stops working without any apparent...
I'm using the NCS 2.5.2 sdk and nrf 5340 with 7002, and I want to do BLE OTA DFU using external flash.
I've found this guide Add DFU support to your application - Software...
Hi,
I am learning my way with Zephyr on nrf5340 SoC, an loving it so far. Unfortunately I got stuck on something that should work out of the box, the setup of the BLS subsystem...
Hi
I want to use button interrupt in NCS.
There is no button interrupt enabled in initialization.
My test environment:ncs2.6.0,nRF52840DK.
In nRF5SDK, I only need...
Hello,
I am experienced working with Arduino and have developed projects with the XIAO BLE that has an nRF52 in built.
Right now I am developing a software using the nRF52...
Hi,
I try to install nrf connect SDK using the nrf extension in visual studio code.
I get error messages like :
[west]: fatal: unable to access ' github.com/....
I have developed the low-level drivers for the MT29F4G01ABAFDWB (using spi) NAND flash and am currently using the Zephyr RTOS. I would like to integrate FATFS into my NAND...
I'm still a beginner，I don't understand why the board I designed can't run the nRF connect SDK application, but the nRF5 SDK 17 application can run normally. I want to know...
Hi,
I have been using the nRF52840 Dongle for at least three months without any issues. First, I implemented my project on the nRF52840-DK, then easily configured it for...
Hello,
In my code, I would like to use the power_down_unused_ram () function. I included the ram_pwrdn.h file but the build returns with undefined reference to `power_down_unused_ram...
Hello. I want to the use pwm_library example for setting a PWM on a GPIO. It works well except that the initial state of the GPIO is high for about 230us before the PWM starts...
I am in the process of adding LE Secure connections to our project and am having trouble and receiving lots of errors while attempting to Makefile it. We added nrf_ble_lesc_request_handler...
Hello,
Developing an application where we want to use CAF but I cannot get it to build properly. I have created a minimal example that does not work locally for me. Following...
The nrf52840 defines 4 pwms. Attempting to enable pwm1, pwm2 or pwm3 using pinctrl through a device overlay results in build errors suggesting there is something wrong with...
