We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello, we currently use nRF52832 in our product. For the next generation of this product, we are hoping to upgrade to a new module that uses nRF52833. However, this is only...
We have a well-vetted software environment what uses SDK 15.3.0 and softdevice s132. We are considering adding ANT+ to our environment, which as I understand requires that...
I am in the process of bringing up a custom board with an nrf5340 and a FUSB302B USB-C PHY-controller.
As a driver for the FUSB203B, I am using this project as an OOT-module...
Hello
Due to some reasons we need to use external antenna and RF cables.
What is a part number of the antenna that can be connected to the J1 RF Antenna connector?
We...
Hi,
I am implemented the uart functionality, I'm getting below issue.
[00:00:00.445,526] <err> Throughput: Failed to set UART callback (err -88) [00:00:00.445,556] <err...
I want to use LPCOMP in nrf52832 to detect a rising edge of voltage. And my code is:
I set the reference as NRF_LPCOMP_INPUT_1 or NRF_LPCOMP_REF_SUPPLY_4_8, the event is...
I am running on openthread demo: ot_cli on its low power mode by building with low_power snippet.
As document says, it will automatically suspend UART operation when low...
Hi,
I'm trying to use to gpio pins in order to wake up a system from sleep mode.(PIN1= P0.24 PIN2 =P1.1 )
If I use the GPIOTEs separately in my project, it works and sytem...
There are some serious issues in the file "board.c" that relate to LEDS_NUMBER.
If I create a custom board with no LEDs then I set LEDS_NUMBER to in my custom boards,h....
Hello,
My company has developed a Bluetooth application that runs on the nRF52832 and we are about to perform FCC pre-scan testing next week. In order to prepare for this...
I want to use one device (nrf5340 audio DK) as both a gateway and a headset. Is this possible?
It needs to both receive audio from a CIS gateway and send it out, working...
Hi Team, I need to integrate FreeRTOS into the ble_app_hrs_nfc_pairing example. What are the ways to integrate FreeRTOS into ble_app_hrs_nfc_pairing? I need to create two...
I have bought an nrf9161-dk and following the documentation, I was installing the asset tracker using nrf-desktop v.4.4.1 (because v.5.0 crashes everytime I open it in full...
I am aiming to connect the Gateway and Headset 1:1 and output stereo from the Headset.
The Gateway side is 16-bit I2S and the Headset side is 32-bit I2S, and I am able to...
