Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
As well know, there have a nrf_delay_us() function can execute very short delay time, but the function can only "delay".
If I want to create a 1 microsecond continuous...
How are the 28-UFBGA pin assignments translated to numbering used to specify I/O pin numbers in the code. Is this as simple as P0.0 => 0, P0.1 => 1,...? I have seen similar...
software:ncs2.5.1
chip:nrf5340
hi professor,
I want to use dtm to test blue RF. After i compile dtm example by vs code and download merge.hex by nrf connect sdk programmer...
Hello,
I am experiencing an issue where ble_nus_data_send returns a value of 0x08. I would appreciate any advice on how to resolve this error.
Symptoms: The device ...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I used UART for communication between...
This is my log output when i connect to my ethernet
this is my prj.conf file
I am building the default AWS_IOT_MQTT SAMPLE. i dont know where i am getting the issue...
I want to implement a network of boards to be placed in a field. We have sender nodes(boards) which will collect data through saadc channels and transmit it to receiver node...
Hello,
i am developing a bootloader with softdevice112 on nrf52805.
I have setup everything and I can see bootloader and app working, just a question about memory layout...
I can't use the I2S api and I2S function in code the compiler says undefined Module , and when i checked the devicetree file there in no definition for the i2s devices
Hello,
I am programming BLE with the nRF52840-DK.
Toolchain Manager: v1.3.0
IDE: Visual Studio Code (VSCode)
SDK: ncs v2.6.0
My implementation goals are as...
With the change from nRF51 to nRF52, the data rate became a minimum of 1 Mbps.
Nordic proprietary radio mode,
nRF51 250 Kbps.
nRF52 1 Mbps,
What is the difference...
Hi everyone,
I working on a project which is a BLE peripheral with Zephyr,
I need to implement the DTM testing for production testing. I created my project base on NUS...
Whenever I respond to a question I opened myself, it generates an "Unread Notification" alert and an email.
I don't need either the website or the email to tell me that...
Hi everyone,
I trying the DTM example and run with debug, I found the software stuck at dtm clock initial. what is the problem , and how can I fixed it , thanks.
...
