We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I originally developed the product using the nRF5 SDK with C++. The functionality is already implemented, but due to high power consumption from the C++ version, I now plan...
Sadly not in the documentation and the sizes changes from 5.0.0. I did try using the 5.0.0 but it doesn't boot (could be another problem). Thought I'd ask anyhow.
I have managed to use 3 nrf5340 audio DKs one configured as Gateway and the other two as left and right headsets to stream stereo audio. My question is, what do I need to...
I’m working on an nRF52-based design where the device should remain in System ON low-power mode after an operation (SAADC sampling + BLE sync). After SAADC data collection...
Hello,
My application uses three nRF5340dk for LE Audio: two Unicast Servers and a Unicast Client. The Client scans for servers, establishes connections, performs discovery...
Hello, I'm using the nrf5340 Audio development kit with SDK Manager v2.9.0 and a micro SD card, and when I try to play the audio as indicated in the development example in...
Hi, I have the following situation:
I have a legacy C application that runs on the good old nRF5 SDK on NRF52840 with FreeRTOS. (No BLE on the application, but the bootloader...
I am trying to repurpose NFC1 and NFC2 pins for GPIO usage, but they do not function as GPIO, while other GPIO pins work correctly.
SDK: nRF Connect Bare-metal SDK v0...
Hi Team,
Below function returns error code as -5 and unable to write and read data from I2C peripheral.
err = i2c_write_read ( i2c_dev , addr , write_data , write_size...
Hi,
so i was using the NRF51822-QFAC with an external balun and this antenna chip 2450AT43A100E .
now i want to move to the nRF52832 chip and from what i read is that...
hi support team,
customer is ordering sims from network supplier, and i got one sim card, but after testing i found this sim card can't be recognized.
here is the modem...
Hi
We have developed a remote-control system where both the sender and receiver are built around nRF52840. Today, the SDK is sdk-17.1.0. We are now considering moving over...
Hi Nordic Team,
I would like to use a USB camera in my project with the nRF5340. Is this possible? If so, could you please share any reference documentation or example links...
Hello all,
I am currently using the nRF9160 DK for cellular uplink to our server for an evaluation. From the nRF connect software I use the provided firmware 'AT Host' and...
