We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's, and I have been working for a while now on getting myself familiar with the audio application, but I have...
Hi,
I'm trying to run the zephyr/samples/drivers/adc/adc_dt example on the nRF54L15 DK .
I modified the board overlay file zephyr/samples/drivers/adc/adc_dt/boards/nrf54l15dk_nrf54l15_cpuapp...
Description:
I'm having an issue with my nRF52811 custom board where the device won't start BLE advertising after programming, but it works after cycling through GDB monitor...
Hello,
Following the NRF54L Express course I see that PWM duty cycle can be updated from RAM via EasyDMA but I can't see an example of how this can be done anywhere...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
When i flash i always get the this error: before this i had an another sensor the VL53L0X which worked perfectly.
[0Sensor device not ready! 0:00:00.254,119] <err> VL53L1X...
We are trying to develop a smart controller based on the nRF54L15 that supports a dynamically configurable number of buttons. We want users to be able to select the number...
Hi,
I’m trying to explore the capabilities of DECT NR+ technology using the nRF9151-DK. Are there any recommended external antennas that I would be able to use with this...
Hello,
we are building a custom PCB using the nPM1300. We need a low-noise 1V8 rail for a sensitive analog component and are wondering what the best setup for that would...
I’m working with the CRACEN peripheral on the nRF54L15 and I’m trying to understand the DMA User Tag field used in registers like `CRYPTMSTRDMA.FETCHTAG`.
The documentation...
Hello,
i'm working on a matter sensor on a nRF52840 Dongle and BME280.
The softaware is based on matter/temperature_sensor with config changes to support nRf52840 Dongle...
We are using the Nordic Semiconductor nRF7002-DK . In this board, both PS-Poll and No-PS-Poll power-saving modes are working as expected. However, when running in TWT (Target...
Hi,
we have a issue to find the right configuration to get the maximum throughput in a multiple connection scenario.
In our setup, we are using one central and three peripherals...
