I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello and thank you for reading. We are using SDK 2.5.0 and the nrf5340, and would appreciate some help with the HID over Gatt functionality.
Our device implements multiple...
I have an application for a mouse with nRF52833, s140 and SDK17.1. The BLE advertising works in fast and slow advertising, and I'm following the indications by Microsoft on...
I'm trying to port a PPI application to an nrf5340. I'm quite puzzled, as it would appear there is no obvious way to achieve what I'm trying to do.
In short, I have a setup...
Hi,
I notice that every time I can only send 244 bytes per time in nus service, if I set higher I will not receive the data in RX.
But I also see that the thoughput...
Hello,
We're using version 7.0.1 of the S140 soft device. We are making a bluetooth application where the device behaves both as a central and peripheral. In peripheral...
we now have nRF52840 DK PCA 10056 , V3.0.0 . the documentation of product specification user guide available online is for v1.0 (old dk) , but not for v3.0 . please can you...
Hi folks,
I am just in the process of getting my feet wet with the nrf connect sdk and zigbee development is my ultimate goal.
I am using an ItsyBitsy nrf52840 https:...
Wireshark Windows version 4.4.5
nrfutil 7.12.0
ble-sniffer version 0.14.1
Somehow during the course of installing the nRF Sniffer, Wireshark got two interface toolbars...
Hi,
I'm working on a very high density board with the nRF54L15-QFAA (we want to prevent using a CSP) and I'm running into some routing issues. While looking for optimizations...
Hello, We faced with issue in which we are not able to get the time from the network and because we don't have time, we can't use JWT. As I understood issue is because of...
Hello everyone, I am want to write custom radio protocol for the nrf5340. I have already tried the ESB protocol. But that is somehow limited on the latency (I will open a...
I'd like to use the nRF52832 for cost reasons & I know there are different Bluetooth audio standards, which the nRF52832 does nto support the latest. I don't need hi quality...
Hi, I have a question about the WDT documentation in nRF5340 Product Specification v1.6.
Question 1:
The chapter "Reload Criteria" (7.41.1) is maybe a bit ambiguous defining...
Hello,
I am using the LTE IoT 4 Click board based on the nRF9160, with SDK version 2.6.0 and modem firmware version 1.3.6. I read in the documentation that the nRF9160 provides...
We are developing digital stethoscope and would like to use nrf5340-audio DK as starting point. We need to first get the microphone out on the headphones jack in the DK and...
