We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello Nordic Family. I hope this post finds you well.
I am working on a project where I have connected multiple sensors to the NRF52840. I have collected all the sensor...
Hi,
I have a quite controversial question I want to ask! I am new to the world of Nordic Semiconductor chipset and I need some information in order to decide which way to...
Hi I am trying to run the exampls of dwm1001 git file of ex_11b_leds on dwm1001 dev board using SES it gives me an error on Zephyr.h file , how can i connect to the nrf connect...
I developed a product for the customer with 9160. It used to run on the sdk of ncs1.2.0, and its fota function is normal; Now I have upgraded the sdk to ncs1.9.0, and found...
Hi!
Working on a BT peripheral device that will work in two modes depending on a runtime check at startup:
Sending data over BLE, running on battery (UART unused).
Sending...
Dear Support
I am developing a central application, scan and send out scanned packets via UART to host MCU, where I am thinking of calculate the advertising interval by...
Hi! I followed the recipe described on nRF Sniffer for Bluetooth LE to flash the sniffer .hex file into my dongle, install and configure the wireshard.
When I start the...
I am trying to install using VS code, using the video
https://www.google.com/search?q=install+nordic+visual+sydio+code&oq=install+nordic+visual+sydio+code+&aqs=chrome..69i57...
Hi everyone, i am new at this platform.
In my project, i need to take gps data from uart and send the data over zigbee with nrf52833. I haven't found any example and don...
Hi All, trying to find a cause of this problem, we have two devices, one is acting as peripheral and one as master.
Peripheral: ( nRF52832, s132 v7.0.1) a remote wireless...
I am trying to make a build with a slightly modified copy of the Zephyr button example on a nrf9160 board with a upgradable bootloader.
The following command can build our...
I seem to get error 4 on nrf_sdh_ble_enable when building and running the application in release mode.
Everything works perfectly when building in debug mode and I've checked...
Dear Ladies and Gentleman
Regarding the Bluetooth SIG Qualification the BQC needs a QDID for the Softdevice Controller Subsystem ( from table 2 of the compatibility matrix...
when i debug samples in Zephyr, i can see log through UART when i use "printk" function.
but i find there has "BT_DBG" and "BT_WARN" in code. so what's its using? and where...
