At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
When asking to change the toolchain version in the VSC extension I get an error message:
Command 'nRF Connect Select nRF Connect SDK Toolchain' resulted in an error...
I am using the current nrf-sdk v2.1.0, which includes a Zephyr version (3.1.99 etc.) which has at the used stage an error with twister: instead of using get_testsuite the...
Hello,
I tried to run the sample Bluetooth: Periodic Advertising but I found some issue.
I'm using SDK v1.9.1.
The first issue was related to advertising creation with...
Before I go deep into the rabbit hole, I am wondering if anyone has had success with the following:
I am in a Windows 11 environment
I want to setup Docker with nRF...
Hi Community & Nordic Semi
I have an ultra low power design using the NRF9160.
I would like to avoid adding an additional LDO to reduce costs and Iq.
VIO from the datasheet...
Hello Community, i'm currently working on a custom board based on BC40C which is a BT/BLe module based on nrf5340 i'm trying to debug my board with jLink ultra + under, i...
There is an examples that show how to change from a 2Mb/s to a Coded 125Kb/s ?
May I change the bit rate of the comuniucation dinamicaly ? For examples I see that with a...
Hi there,
The mentioned known issue needs a workaround requiring a soft reset. This is quite a bruteforce method and I can't believe this hasn't been fixed already. Quite...
nRF Connect SDK v2.0.0
VS Code 1.70.2
nRF9160 development kit
To view all possible log messages the fololwing logging configuration is set up in prj.conf:
CONFIG_LOG...
I'm using nrf52832, and it is connected with external mcu (stm32) to uart.
I'd like to connect this ble module to PC with ble (wireless connection), it was paired.
After...
Hello,
We developed a zigbee coordinator with nRF52840.
We discovered that our coordinator is not receiving the the beacon request coming from some Ember based sleepy...
Hi,
Is it possible to connect the Thingy53 over Bluetooth with Raspberry and store the sensor data in a database (e.g. Firestore).
I only found one solution, but its for...
Hi,
Is it possible to get the device name - i.e the GAP_DEVICE_NAME - of an unprovisioned or provisioned device using a serial device and the interactive_pyaci? It would...
Hi everyone,
at the moment we are trying to upgrade our nRF9160 software form the SDK v1.8.0 to the newer version SDK2.0.0. The main issue of the migration is our UART implementation...
Hi,
I'm using NCS v2 and VSCode on a custom board, and the android nrf connect app.
The board which has an external crystal, which I am not trying to use, in favor of...
