At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, im trying to implement the UARTE Driver for simultaneous Use of Bluetooth and asynchrounos Uart TX/RX on a nRF52840 and nrf9160. The Problem is that neither RX or TX...
Hi
i want use a nRF52840Dongle as a Zigbee end device, when power up, i get following message:
I: nRF5 802154 radio initialized ***** delaying boot 5000ms (per build configuration...
Hi, I have just started evaluating nRF52840 using the dongle and Development Kit. I have successfully tested the Openthread network using CLI project. Now I want to try out...
Hi experts, The situation is following, the NRF53 shall receive multiple packets. After the reception of one of the packets the next one shall be received at the same frequency...
Hello,
I am struggling to commission a light bulb matter sample device (nrf52840dk) with the CHIP tool running on my Linux laptop. I set up an OpenThread Border Router with...
I had configured zephyr.dts file for UART and I2C pheripherals. And when I tried to build an application it is giving below error
Board : nrf5340 Application name : SHT...
I implemented the nRF52840 (auto)upgrade with an nRF9160 on the nRF9160DK. I did my development with the Serial Modem LTE application from nRF Connect SDK 2.0.0. I noticed...
Hey All:
I'm trying to install V2.0.0 of the NRF Connect SDK on a fresh Ubuntu 22.04 VM, and the whole thing seems broken.
Here's my steps:
install the nRF command...
Hi, I have found several aged topics on Devzone but need this feature and would like current state. If it still not supported, is there any example implementation on how manage...
Is there a way to rebuild (clean and build) a project in Visual Studio Code with the nRF Connect Extension? A web search shows how to do it with the CMake Extension ( https...
I am using the Connect SDK v2.0.0 and attempting to use TCP in the stock CLI example to mimic the demo shown here . When I flash the v2.0.0 CLI sample on my nRF52840dk, "...
Hi everyone,
I have some devices that are communicated through RS485. nRF52840 DK supports RS485 communication?
Do you have suggestions of how should I connect those devices...
I have a custom board with 8 LED's and I use pwm API led_on(), led_off, led_blink() etc, to turn them on, set brightness and blink and everything works fine except one case...
I am using nRF52833 DK and I am running Light switch server in one DK and Client in another DK Advertising interval was way too high(around 9Second) so decided to change it...
Hi
According to Amazon documentation, it is possible to connect a smart home device to Alexa with the Bluetooth Low-Energy (BLE) mesh wireless communication technology....
