Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi!
I'm developing a small central BLE software, everything works well, please assume that I have correclty instantiated a connection, did the service and characteristic...
Hi,
I have looked around the internet and am trying to understand the ble security options. I cannot understand the correct approach to take for our application.
Our situation...
Hi,
How interrupt is working in nrf saac driver? I can see that it is already code is present in the adc_nrf_saac.c
static int init_saadc ( const struct device...
Hello,
I was wondering if it is possible to port older projects built using the now deprecated Nordic Thingy:52 SDK ( https://github.com/NordicSemiconductor/Nordic-Thingy52...
Hi,
As a university we bought several NRF51422 dongles to sniff BLE traffic
Following the installation instruction here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hello,
I am new in nordic previously I was working on Cypress controllers. I am trying to put the device in System ON Low power mode.
I have tried the below functions...
Hi,
I am working on a project using BT Mesh and I am evaluating a prototype using the nrf52840. I am not working with the mesh-SDK, because I am using zephyr. I am working...
Hi, I have a University group project which required us to build software on Android devices. Basically, this project requires us to build software based on BLE Mesh between...
Hello,
I want to communicate one card nrf5340dk with 2 same card in using 'central_uart' and 'peripheral_uart' samples.
I have succeeded to establish the connection and...
Hi,
We have a new product and are looking into OOB pairing for authentication and encryption. All the information about OOB flows back to NFC pairing, but that is not what...
Hi
I am working on an application that uses extended periodic advertising feature of BLE 5. In this sample (periodic sync):
https://github.com/nrfconnect/sdk-zephyr...
Hello nordic. I have several SPI peripherals connected to the nRF9160. I'm using the PPK2 in ampere mode. Does this then also measure the additional current drawn by the SPI...
Hello,
I'm wrapping up the layout of a board based on the NRF52832 (DCDC). I've tried to replicate the reference design as close as possible. I'm using Kicad and had to...
Hi,
Referring to the case,
https://devzone.nordicsemi.com/f/nordic-q-a/72660/nrf-connect-sdk-v-1-5-0-how-where-to-change-phy-and-tx-power-for-long-range-application
...
