At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
Facing some issue in creating sample application in vscode
nCS sdk V1.7.0, created sample hello world project and added build configuration for bl653_dvk
getting...
Hello all. Now I am making a BLE network with multiple peripherals and central based on NUS. How could I make data transfer between the central and specific peripherals? I...
Hello,
I would like to develop OpenThread applications that run under ZephyrRTOS for the nRF52840 processor. It appears that there are 3 possible development approaches...
Hello I'm trying to implement the DFU Trigger library into my project. to get following function:
" When the trigger library is added to an application, it allows a connected...
Greetings,
I am trying to get the nRF5340 DK to run on the coin cell battery attached to it. I removed the plastic and the USB cable then I put the "nRF power source" switch...
Hi team,
When we set fast advertisement timeout (uint32_t ble_adv_fast_timeout; /**< Time-out (in units of 10ms) for fast advertising. */) to a value greater than 0xFFFF...
i am using Laird smartBASIC for my programming of the BL653. I cloned the firmware of the evaluation board using the supplied Laird batch files and the J-LinkARM interface...
Hello, I have a question that I can't find an answer to in the documentation. The answer may be somewhere and I am just unable to find it.
My application utilizes sd_ble_gattc_write...
is it possible add dfu service and central uart both into nrf52820?
using D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c
SDK_17.0.2
Dear Nordic Bluetooth experts,
In the Android-nRF-Mesh-Library , is there a way to mark a unicast address as used? The reason why I'd like to do it is the following: When...
Hello, All,
I am using nRF9160 for product development and would like to know a few more important parameters:
What is the power consumption of an NB-iot network using...
Hi There,
I want to connect programable pins on nrf52840 chips in the schematic.
Can you tell me which pins are for programming and debugging?
Best,
Gaosheng
What does this error mean?
<error> app: ERROR 3735928559 [Unknown error code] at c:\nrf\modules\nrfx\hal\nrf_gpio.h:492 PC at: 0x00033D23 <error> app: End of error report...
