Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hello, I have developed a program that reads (with I2C) a temperature sensor and sends it to the central board. The central board is a NRF52480-DK. I have tested the peripheral...
Dear Sir.
I was testing dfu mode with an nrf52840 dk and held down the IF BOOT/RESET button, then powered up and waited a few seconds before it went into bootloader mode...
Hi,
I'm evaluating the NRF52832 for an ultra low power BLE application where I'm going to use GATT. I've built some prototypes with the NRF52832 and right now I have to...
Our engineers have two questions that they are confused with:
1) When applaying ble techniques, does nodic 52 serious of chip compatible with SIG mesh?
2) When applaying...
Hi there,
we are working on getting type approval certification, and the test lab is asking for fixed frequency software, drivers and SOP.
What we need is the fixed frequency...
Hi,
The actual problem: I want to store some stuff to flash at factory, that is never erased. And I also need another persistent memory that can be written in runtime. I...
Hello I am now trying to implement an active NFC Tag using nRF52832. But I don't know what that example project is. Can you point to a command or example source that performs...
Hi,
nrf-sdk: 1.3
Firmware: 1.2.1
Using offloaded sockets(secrets at the modem side)
My use-case is this: Provision PSK and identity to device at the factory for DTLS...
Hello,
do you have any method, example or other documentation to recommend to me in view of implementing the storage into non-volatile data with our thingy91 ?
we use...
Hi team,
Is it possible to route the low frequency clock inside the nRF9160 to an external device? If not, then the only option is to generate the clock using the timer...
Hi,
We use the nRF radio timeslot API to take control over the radio and other peripherals periodically. We have noticed that when the timeslot is active (we own the peripherals...
I tried to use the Bosch BSEC library for the Asset Tracker application for nRF9160.
It seems that the Asset Tracker was build for BSEC 1.4.7.4 which is unfortunately no...
I develop a test fixture based on nrf51 code that I use for final product.
NRF51 is just a part of a complex test fixture, then I have just "one" test fixture model.
I...
Does m_xfer_done need to be set to false before calling nrf_drv_twi_rx? If so, does while (m_xfer_done == false); loop need to be called on every read?
