We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello,
I have a device that samples data from a bunch of sensors every n hours, and that when in IDLE must consume around 100uA. To achieve this, I'm using a counter (that...
Hi,
I connected MCUBoot and FOTA to my project. I checked that the download is working, but not stable. I saw in the documentation that you can enable the continuation of...
Hello I need a falling edge response via GPIOTE. The settings I use for sdk 16 to sdk 14.2.0 do not work. For sdk 16 I use the functions nrfx_gpiote _..., for sdk 14.2.0 nrf_drv_gpiote_...
I observed a peak of 334 ua during system-on low-power mode during idle time which is periodic around 4 sec. I am using ble with RC clock option.
1.is it waking for calibration...
Previously, I learned that BLE is capable of 1:1, 1:N, and N:N communication, but I didn't get the exact information. Can I get some information? How do you do it, what's...
What is the max current nRF52840-DK source from Vdd pins, i am connecting multiple sensors through the Vdd of nRF52840-DK i want to know how much load it can source ?
Hello,
There is a problem printing the log message. I am using SDK12.3, keil compiler and segger J-Link. After modifying the project a little, normal log output is not available...
Does the nRF9160 have an ATEX component certificate? Why there is no marking such as "Ex ia IIC Ga" provided? What exactly do you understand by the term "ATEX compliance"...
After a conversation with a Nordic engineer and some research it looks like there is no official way to upgrade a product over the air from an nRF5 SDK based product to an...
I ported the Thread Secure DFU example to use FreeRTOS, however I get a hard fault if something is scheduled using the app_timer provided.
Calling coap_dfu_trigger or handling...
We have a custom PCB fitted with the nRF52840 SOC, we've previously erased and written to it via the nRF programmer tool. However, when trying to use the nrfjprog -e command...
Hi. I am having trouble connecting nrf5340 PDK to nRF Connect app on my phone.
I am using the peripheral_uart example based on https://infocenter.nordicsemi.com/index.jsp...
My customer is using a Taiyo Yuden module, EYSLSNZWW, that uses the Nordic nRF52810 chipset. We need to configure the board for Bluetooth Qualification testing. I have read...
Hello,
I use the TP4056 charging module and the 3.7V lithium battery (300mAh) and work on sdk v17.
One of the features I'm trying to create is when the charging connector...
