I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi,
Sometimes our custom board is not readable with the reader uTrust3700 from Identive and it might be related to this post . We are usind SDK 14.2 with our custom board...
I'm using nRF52832 and intend to interface 3 I2C slave devices; the first is the BNO055 IMU.
I've integrated the Bosch "driver" code into my SES project, but I find that...
We are implementing a DFU controller to perform DFU over serial for the nRF52832.
Our reference is the nRF5 SDK v15.3.0 DFU Serial documentation (Nordic/SDK/nRF_SDK_15.3...
There are a few threads on here about this already, but I wasn't find the answer to the exact question I had.
I am using the nRF52832 with SD132 and SDK15.2 on a custom...
I cannot get logging in the Seggar debug terminal nor the J-link viewer application (All terminals) when running this example.
I have the NRF_LOG_BACKEND_RTT_ENABLED selected...
Hello
I am using nrf52840 from nrf9160dk, I am trying to run example from nrf52840 with sdk16.0.0 and sd7.0.0. While checking data on uart I am getting following error...
Hi
I'm trying to get a DFU boot loader working on our own custom hardware. My initial approach was to build secure_bootloader_ble using my own public_key.c file and try...
I updated my Thingy:91 today to version thingy91_fw_2020-04-29_bc7ade8b.
I flashed the mfwnrf9160120, the thingy91_nrf52_connectivity_bridge_2020-04-29_bc7ade8b and the...
Hi, I'm developing firmware for the trf7970a nfc chip. For standard communication the chip uses spi, but a special direct mode uses an additional two wire interface where...
Do the values for current consumption given for the scenarios in Section 5.2.1 of the nRF52833 PS include the current for any peripherals required? E.g. the PS quotes 2.6uA...
Hi!
I am trying to merge the basic/button sample with the mqtt-simple sample.
I added to the prj.conf of mqtt-simple sample.
My main.c looks like this:
After merging...
Hello!
Iam trying to get the spi function to work properly on my thingy 52 device.
My problem is that the transfer wont stop when it should in my opinion, i have analyzed...
Situation: SES, SDK 16, nRF52832
I'm developing a pre-production test program without BLE. I'm using APP_TIMER_V2 and noticed that the timer events do not not happen even...
We have a custom board with nrf9160, ncs 1.2.0 and modem fw 1.1.1. We experience strange behaviour with the GPS: As an example,on units with 30 min fix intervals, we experience...
I added the commissioning part from the nfc_meshcop example to the mqttsn_sleepy_subscriber example. I tested the nfc_meshcop exaple and worked, so the border router part...