At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I'm designing an application using SEGGER Studio for the nRF52832. I have based my application on the template peripheral example.
What I want to do is to trigger...
Hi--
I tried to implement an internally managed RTC using the app timer library, but came to find the error on that is too much for an RTC (~25 min lost over a few days...
I want to know which pins serve the purpose of TX and RX in nRF51822. I suspect its the ANT1 and ANT2 but i want to confirm and also if the following would be a good way to...
I just buy nrf52840 Dongle.
I connect nrf52840 Dongle to my USB port and open nrf Connect.
I look at guide https://devzone.nordicsemi.com/nordic/short-range-guides/b/getting...
Im using sdk 15.2 with 2 nrf52840 boards, i would like the server to connect to a particular client. How to add the devices to whitelist in sdk 15.2 ?. I have gone through...
Hello,
I am working on a scanner code, I have initialize my scanner with this parameters.
and in nrf_ble_scan_init()
It is getting reset once in the beginning like...
Hi,
without any obvious reason one of our nRF52840 DKs stopped being visible over the USB (J2) interface. The nRF52840 is still functional and can be programmed from another...
Hi. I'm using nRF52832, SDK13.0.0, S132.
First of all, I already know this Q has lots of Q and A.
But I'm so confused which case do I pick.
In my case, iPhone has...
I am a student studying zigbee. We succeeded in turning on/off the LEDs of zc_light using examples of zc_light and zc_switch. The question here is, where do you send and receive...
I am trying to duplicate a RF remote control which uses a Nrf24L01+ IC.
I have temporarily connect the SPI interface of my test chip to the SPI pins on the remote, and transmitted...
Hello guys,
I have already created the JSON file and checked it using the online JSON validator and viewer. Now, I am interested to figure out is it possible to use this...
I'm trying to pair my peripheral with the central using BLE.
In the central code (running on windows c#):
In the peripheral terminal:
the device in sending PM_EVT_CONN_SEC_PARAMS_REQ...
Hello,
I'm experiencing a disconnection problem on several BLE Mesh networks. My topology is 1 client with an average of 60 servers, for all networks. Client is connected...
Hi guys,
I have the same issue as coca1989 had 2 years ago . Did anybody found a solution?
I am using health model and simple message model. Client and Provisioner are...
