Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Windows 10, Keil5 5.27.1.0, Nordic SDK 15.3.0 59ac345, pca10056 devkit for nRF52840.
Works:
The DK shows up as "JLINK" when plugged into USB. I can copy the prebuilt hex...
I am currently publishing messages to a group of servers on a 10 second interval. This works well for a while but after a few minutes some of the nodes stop handling the message...
Hi! I am using Nordic Thingy : 52 Iot Sensor Kit. I have Windows x64 computer. I connected the sensor's bluetooth (nrf52832) to the HM-10 bluetooth module. I want to transfer...
I modified mqtt_simple program to test eDRX. This program subscribes a topic right after it is initiated.
I want to test only eDRX so set keep alive time = 30 min
I...
hi,
I am trying to readout the UICR info. But there is no such readout in the hex file using the programmer apps in nRF Connect.
There are 2 possibility, either blank...
Hi,
I am using nRF52832 DK and also my custom board based on nRF52832.
I have uploaded the application file into my device using OTA-DFU.
Now my device goes in application...
In my computer, I receive the error below
Besides that, the error also stated this: "Zephyr was unable to find the toolchain. Is the environment misconfigured?(Refer to...
Hi there,
I'm sorry if I'm asking something very simple:
How does one connect the J-Trace Pro to the nrf52 DevKit in such a way that I can get ETM functionalities? Obviously...
hi:
my chip is NRF52832 (512k FLASH + 64k RAM).
I want to triggle ESB send process by PPI + TIMER ,but i can't find the function like esb_task_address_get()，but i found...
I tried finding a link to a porting guide mentioned in few of the posts in the devzone but couldn't find a working link. I have a project originally meant for nRF52832 devices...
I'm getting confused with the following statement, taken from www.nordicsemi.com/.../S132
"It supports up to 20 concurrent links in all roles."
So, I will try to explain...
Hi everyone,
I am trying to connect multiple peripheral and collect the rssi values of the the peripheral devices in central mode. After collecting the rssi value of the...
I want to send Digital Microphone data from one device to the other two devices. So which BLE and micro-controller should I use for better performance? I am totally new to...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I connected my sensor to nRF52832 DK over TWI...
