We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi, in the documentation for this module there is no stencil design specification or recommended
reflow profile. My earlier experience of LGA-modules says I really need...
Hello,
I want to get the IP address of a CoAP request source (server). According to me, it is close of the objective of the client / server pair mechanism example. So...
Hi, I'm having problems negotiating DLE with a nRF52840.
I'm sending a LL_LENGTH_REQ (251 octets and 2120ms time) to nRF52840 from an ESP32.
According to the spec. those...
Hi
I am using nrf52832 dev kit.
I have configured my device to act as peripheral. i want to discover services offered by central devices whichever connects to my device...
I am trying to use the PA/LNA using the pc-ble driver. To do so, i need to configure GPIO and the softdevice. I found examples:
https://devzone.nordicsemi.com/b/blog/posts...
I'm wondering about how the notification queues are allocated when setting hvn_tx_queue_size using ble_cfg.conn_cfg.params.gatts_conn_cfg.hvn_tx_queue_size.
If I set it...
\components\iot\socket\api\socket_api.h contains a definition for 'struct timeval' that conflicts with \arm-eabi\sys-include\sys\_timeval.h
It creates a conflict with including...
Hi,
This thread discusses how to change the Makefile to interact with the Segger Systemview ( https://devzone.nordicsemi.com/b/blog/posts/instrumenting-with-segger-systemview...
Enabling or disabling notification on Client does always lead to an update of local database of Server by writing to its flash memory. Particularly NUS requires enabling of...
Hi,
I'm following this tutorial . In challenge 1, I was asked to change the transmit power level of the device.
Challenge 1: Try to add and populate the "p_tx_power_level...
Hi,
I am trying to integrate some ble code into my project but it keeps giving me errors like:
Error[Li005]: no definition for "ble_advertising_on_sys_evt" [referenced...
While developing code for our custom board, we ran into a filesystem corruption issue with fatfs+qspi block device and multiple directories. We were able to reproduce the...
I have problems running the ble_app_uart_pca1004e_s112 on a custom nrf52810 target devivce. The custom nrf52810 target is a custom board with the Rigado BMD 330, which is...
Hi there,
Please see the video for a full run down: https://www.youtube.com/watch?v=nIeIUMutBlU
Basically, I have a perfect and verified design that's been in the...
