We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
nRF52, SDK15, S132
Hi! After few days work I have stop scan from my central device on the nRF52832.
I can't to understand reason of this. But I need to know is scanning...
I downloaded sdk15 for nrf52832.all sample programs and soft devices are working fine but boot loader coding is showing some error. I am using this bootloader code install...
Are there example scripts to take readings or communicate with other devices over serial? Like, if I attach a temperature sensor, distance sensor, etc, I want to read from...
Hi there
I was going through the errata sheet and discovered the PAN #88.
It states that the current consumption is increased when entering System ON Idle within 125us...
If I just comment-out battery_measurement_init() in main():
Advertising does not start, I see nothing on the UART CLI, and the RTT log just shows:
With battery_measurement_init...
All examples shipped with the SDK have the same compile problem
components\libraries\util\app_error_handler_keil.c(47): error: A1198E: Unknown operand
The offending line...
Hi to all,
i had developed an app for PCA10056 and now i want port it on PCA10059, there is any guide or white paper that indicate how can i done that??
i read in the...
I've just started evaluating the nRF52840 DK and running into an issue when attempting to run any of the multiprotocol ble_thread examples.
I've downloaded the "nRF5 SDK...
Hi
I'm using the NFCT peripheral of the nRF52832 Rev. 1.
What is the intention of the LOCKDETECT field in the FIELDPRESENT register? I don't understand the description...
I can't connect to my nRF528540-DK anymore after I connected an external power supply and switched SW10 to off. the external power supply is 5V. my DK doesn't show up in device...
Hi
I open the SAADC to get the battery after initial the SAADC, using nrf_drv_saadc_sample_convert to get the ADC data . After nRF52832 is initialed, it enter power_manage...
Hello I'm using a nRF52810. Now i'm trying to add an PCB antenna to my Altium sheet i Wrote in another Reply that i could use the one from your USB Dongle but i don't find...
Hi there,
I need realtime data monitor, but the power consumption is too large when BLE sending data continusly. So I wanna know wheather NRF52832 support package the...
Hi,
I am not yet familiar with NFC.I s it possible to read battery data from the NFC tag of the nRF52 to another device (for example a smartphone). I want to write simple...
