Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi I`m new to nrf so pls forgive me if this been asked before. 1. nrf52840 dk. Flash twi_scanner_pca10056 via nrfgo, verify ok.
2. At the moment I have no I2C devices connected...
Hello! I had asked a question about zigbee to parsing xiaomi data here . But there is no answer for my last ? .
tomchy adviced me this solution:
...
- register an endpoint...
Dear Sir, we are developing an application on the nRF52840 kit with SDK 15.0.0. We are using Keil as compiler. In our application we need to receive data from two uart together...
I have a test program that does a simple call to fds_record_write() to write a 4 byte value to an FDS file. This is using the NVMC backend. I happened to stop the debugger...
Hi!
Can anyone from Nordic pinpoint where exactly in buttonless project or bootloader project NRF_DFU_SVCI_ENABLED definition is used? I mean 15.0 and 15.2 SDK.
I have...
Hi, i need an advice.
It said in nRF51822 datasheet at p.11.1 (PCB guidelines) that "The supply voltage for the chip should be filtered and routed separately from the supply...
I have upgraded to the more recent J-link RTT Viewer.
If I start Debug Session in uVision and run RTT Viewer, I can connect just fine and have checked the Existing Session...
In the nrf5 sdk (version 11.0.0) there are three different modules which, as near as I can tell, do the same thing. These are:
pstorage
fstorage
ble_flash
...
hi........... nrf523
how to read the data from peripheral and send the data over ble using ble uart
i have merged the two programs ble_uart and twi sensor ,what changes...
Hi,
I'm trying to flash the mesh lightswitch example on Bluemod S42 custom board, please help me with what are the steps to be taken to flash on custom board.
Hi,
As the tile says, I'm using BPA600 capturing mesh logs and analyze.
Since BPA600 needs to configure "MeshOptions.ini" to be able to decode the logs, it needs "IVindex...
Hi
I would like to debugg my Nordic (nRF52832) custom board at 1.8V with a 6 pin Tag-connect connector ( see here ) and have a couple of questions regarding...
Hi,
I'm trying to compile a simple example (light_switch_dimming_server_nrf52832_xxAA_s132_6.0.0) for Bluetooth mesh with Segger embedded studio. I'm having a hard time...
