Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello team,
I attempted to measure the sleep current on the nRF54L15 DK board, but I’m seeing a very high current draw of about 74 mA.
I built and compiled the peripheral_power_profiling...
Hello,
We are developing a custom board that uses the nRF54L15 chip, and are trying to flash an application along with MCUBoot to allow for OTA updates. When I flash the...
Hi Nordic folks,
I'm trying to get the nrf54L15 in a Fanstel BM15M to go into the system OFF state and be woken up later by a timer. All the documentation I've seen says...
What's minimum hold time for a pin reset on nRF54L10? https://docs-be.nordicsemi.com/bundle/ps_nrf54L15/page/pdf/nRF54L15_nRF54L10_nRF54L05_Datasheet_v1.0.pdf doesn't state...
Hello, I am developing an application that uses Bluetooth Channel Sounding, and for that reason I need to have two devkits connected to my computer at the same time, but the...
Hi there,
I was designing an add-on development board to go onto the development kit to test a 1.8V application. I need VDD:nRF on the 54LM20 to be set as the same as VDD...
I connected the new nPM2100 EK to Linux PC and opened the nPM Power UP application. In the app I'm able to select the EK. The nPM Power UP tells me that " Programming required...
I have an NPM1300 demo board. After testing, the default voltage of VOUT1 is 1.74 V. If I use this voltage to power the VDD of nRF54L15, will it affect the power-on reset...
Hi Nordic
We plan to use 54l15+7002e, how much storage will spend for nRF7002 up layer stack and application(e.g typical Wi-Fi STA with TCP client connections)?
What I've tried:
Testing Summary: SD Card on Port 2
Setup : Wired an SDHC card (Transcend 8GB) to the Connector P2 (middle header) on an nRF54L15 DK v1.0.0...
In my code, I find I can start up the ble pakage sending. but it alway send out without stop. I need send out one package. and stop. In my radio callback. I do call this task...
Hi Nordic Support Team,
I am working on a Matter application using the nRF54L15 , and I have a few questions regarding the external flash configuration.
I noticed that...
nRF Connect SDK v3.2.1, nRF9160dk
Hi,
I'm working on an application which connects to a MQTT broker over cellular network, and have MCUMGR enabled for firmware updates...
Hi，
There are 8K functions in nrf_desktop, but this example is too complicated. My own example is relatively simple. I want to integrate 8K functions. At present, overlay...
