Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I am currently using the NRF_POWER->GPREGRET and GPREGRET2 registers to store data for my custom handling under NVIC_reset . My objective is to identify the cause of a manual...
I designed a circuit using the NRF54L15 to connect via Bluetooth and control several peripherals. I program the chip using the Debug Out of the NRF54L15 DK Development Kit...
I am able to build the firmware without any errors from persistent_key_usage example as below condition
Board: NORA Evaluation Board SDK Version: 3.1.0 Toolchain: 3.1.0...
Hello Nordic team,
I am using an nRF5340 DK with Zephyr, and I am facing an issue where the UART console freezes whenever CONFIG_LOG_BACKEND_FS=y is enabled.
My logging...
Hello, Nordic,
I am trying to use radio test to do FCC, but when I test the example, I found some issues.
When I test it by nRF connect the input may be truncated or...
Hello.
I'm trying to use WS2812 leds with I2S. I'm using two boards for testing: an NRF5340DK and my board based on the HOLYIOT-21069-5340 module.
I'm using a zephyr/samples...
using ncs 3.1.1 how can we invert SW_CTRL0 logic we using a different RF SWITCH then DK
"Does register 0xA4002DC8 (SLEEP_CTRL_GPIO_CTRL) on nRF7002 have a bit to invert...
nRF5340-DK, PCA10095, v2.0.1 and v2.0.2
According the zephyr device tree, the UART0 is mapped to GPIO 0.19/0.20 and UART1 is mapped to GPIO 1.0/1.1 .
According the schematics...
Dear Nordic,
I got some AT commands here <https://docs.nordicsemi.com/bundle/ref_at_commands_nrf91x1/page/REF/at_commands/production_test/xrftest_tx_set.html> to know that...
Hello Nordic Team,
I am currently working on OTA using Sysbuild configuration on the nRF52833 with the nRF Connect SDK .
In this configuration, I enabled overwrite-only...
I'd really like to be able to set the path to nrfuitl in the extension so I do not have to put int on my system path, but rather keep it contained in my project.
Use Case: We are developing a Bluetooth Mesh people-counter on the nRF52840 DK .
Primary: Mesh network for publishing/receiving sensor data.
Secondary: Custom...
Hi,
it seams, that MBED DTLS implementation in nRF9160 firmware v1.3.1 is not compiled with Extended Master Secret Extension https://datatracker.ietf.org/doc/html/rfc7627...
