Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi,
Loaded SDK8 S110 softdevice and application to nRF51822(pca10001), then the application works well. When I want to reload the sofedevice by nRFGo, I get the error message...
Working on a remote monitoring system.
Ethernet solution is on the table now.
But it needs to have extra chipset on board to do so.
I haven't had a chance to look into...
Is there any way i can get UTC time?
Is there any real time clock which keeps track of the time even if the chip is off?
I am using nrf51822 and require the UTC time...
Hey everyone,
I'm having problems with my app's ram usage as you can see from my previous questions.
I've tried this little piece of code:
void memcheck(void){
...
hello friends,
Im developing an application where im trying to connect a central and a peripheral but since the signal strength depends upon run time environment i am getting...
The App ~ BLE Stack is the device, Central is smartphone.
is correct?
I don't understand this sequence.
Do not adv_data_set and the adv_start before the scan?...
I'm attaching a function where I use the sd function :
void edit_speed_ID(uint8_t speed)
{
uint32_t value;//, err_code;
value=5 * speed;
while(sd_flash_write(address...
Unfortunately it seems my post devzone.nordicsemi.com/.../ has been lost.
This is a re-post.
I am trying to manipulate Flash data in CODE_SPACE one page at a time. Currently...
I'm using nRF51822 for ble.
For my application, I need to increase rf power.
( My application needs +10dBm)
In case of CC2540(TI ble chip), there is application note...
Hello,
I have 2 nRF51822 with S130. One is central, the other is device.
I want to exchange custom data between these 2 devices after connection. What is service best...
Hello,
I do communications between 2 nRF51822 (one central and one device). Once they are connected, cant i do a kind of deep sleep and freeze stack state for 1 minute...
I'm getting a hardfault on some float operations that I wasn't getting before I upgraded to SDK 6.0.0 and SD 7.0.0. At least, I wasn't getting them at all before that and...
Hi:
I use spi0(0x40003000) to wirte data to external flash(W25Q64) with SD8.0(sdk8.0.if I write data without sd, it is OK), and when program run to rx_data[number_of_txd_bytes...
A friend of mine asked me to help with thinking about a solution to create a RF communication between 8 robots and 1 access point. Not a lot of traffic, just to signal that...
Hi everyone,
We are making a BLE peripheral that measures some data and keeps it ready for the mobile phone to connect & poll the data.
The data should be private and...
