Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi,
I think getting started with the Nordic chips is not as easy as some others.
I would like to know what are the first things that I need to run my code on a Nordic? Especially...
I just got the nRFgo Dev Kit, and going through the set up I see I need a nRF6310 Motherboard, but I can't seem to find anything about it - like were to buy it.
I just downloaded their iccv8cortex trial version and it includes the 51822 as a target. My 5 minute test drive not withstanding, it looks like this might be a good option...
How to reduce power, for bond connections such as cscs services which only requires communication once per second?
Is there a way to manually / automagically turn off the...
Before I call sd_power_system_off(), I do the following:
NRF_TWI0->ENABLE = 0;
NRF_TWI1->ENABLE = 0;
NRF_ADC->ENABLE = 0;
NRF_SPI0->ENABLE = 0;
NRF_UART0->ENABLE =...
Hi
I using nRF51822 ble_app_uart project with softdevice 7.0.
I need to manage my internal flash memory map so i cannot use pstorage libary test main.txt .
So i try...
Hi,
What is the typical range of operation that can be achieved by nRF51822 Bluetooth Smart Beacon Kit ? I know it depends on the Tx power, but can a range of approx 30ms...
I need help choosing between 2 technologies above, my goal is to enable multiple (up to 20) devices exchange small amount of information (around 30 bytes) between each other...
Hello
How many packets can the nRF8001 send in a single connection event? I have seen here, that it is possible to send up to 6 packets with the nRF51822 + Softdevice S110...
Hi, we've been using nRF51822 for developing application and iOS 7.x detect then just fine.
Since I upgraded to iOS 8. Beacons are 'invisible' to our application.
I was...
When I try to use the mergehex tool to combine all three my application never seems to get properly combined.
What I'm doing:
mergehex -m softdevice.hex myapp.hex -o...
I am using Nordics sample bootloader and I really want to make sure that given a freak accident in sending it the firmware or in the firmware code itself that the bootloader...
Please,
We want to develop our BLE related application on PC and we find that "GAP/GATT driver for windows" is a good way to achieve that. While our system is based on...
