We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi , I flash periodic_sync_conn sample to A and B development boards, and periodic_adv_conn sample to C development board. Only A and C development boards work normally, but...
Hello. We are developing custom boards with the configuration of nrf5340 + nrf7002.
In the previous sta example, a build error occurs when the "Board Target" in "build configuration...
I have customed my own nrf54L15 board and it would run on button battery. I managed to measure the battery level through ADC, but I don't know how to use ADC with nrf54L15...
I've been working for months to try and figure out exactly how to get my application to bond the way I want it to.
I'm using nrf connect sdk 2.4.2 on an nrf52832. I used...
I recently received a nRF9151-DK and try running example "hello_dect".
Apart from setting the CARRIER in "Kconfig" to "1" i did no changes to the code.
Building and...
Hi,
We are facing issue with upgrading our devices using DFU library.
Despite using the latest version of the Nordic iOS DFU Library , the firmware update process exhibits...
Hi,
I know that the nRF52 Dongle should be able to use printk() to debug. I have used it with the Serial Terminal before and it was working.
However, when I program...
I have mistakenly disabled Software Debugger (SWD) and wrote the configuration back to the board. Ever since board can not
(1) Connect and get the configuration data using...
Previously, I successfully completed and performed OTA flashing, and I haven't made any changes to the DFU-related programs since then. However, recently, I have been unable...
Hi! We have tags based on nrf52840 and nrf52833 in the field, running against a central with a nrf840X dongle.
Recently we have had an inexplicable peak in 'Failed to Encrypt...
I want NRFX_SPIM_EXTENDED_ENABLED to be 0. but for some reason it is set to 1. from my current understanding I conclude that the if case here check weather each node with...
Hi
I used the nrf-esl-bluetooth-2.6-branch example to flash the 5340DK (AP) and 52840DK (Tag). I sent the command esl_c pawr update_pawr 9 0 , and then sent the command...
Im trying to clear NVS, it gets cleared but then causes device to reboot.
code in question is :
output halts after Erasing NVS flash memory (0x000f8000, size: 24576...
Hello,
we are developing our first predict with the Nrf52840 running with VDD at 1.8V(default option).
so far we have always programmed and debugged NRF52 devices using...
