Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi I am currently working with nrf5340 board to create Custom BLE profiles for data transfer to mobile app. I am not finding any document or videos that gives me a detailed...
Hello,
In an application with the nRF52832, Softdevice and SDK 17.1.0 I try to use the temperature sensor according to the peripheral example. I attach the temperature.c...
Hi,
when I have the nRF Connect for VS Code Extension Pack installed locally it will break Dev Containers. The following error message will be shown when I try to run...
Hello everyone,
I'm trying to use the buttonless dfu functionality on nRF52 DK. However, I can't seem to test the functionality when there is no bootloader flashed, but...
Dear sir/madam
I'm designing the custom PCB for bluetooth application. I have some doubt on 50 ohm RF line. How to maintain that 50 ohm in track.
Kindly support regarding...
Hi, I have followed the nRF Connect SDK Fundamentals and BLE Fundamental courses and come to Lesson 6 Bluetooth LE sniffer. Everything has worked until this but now I get...
Hi,
In nRF52811-CAA chip, which pins are allocated to ADC inputs. In Table 122 of datasheet which shows pinout for WLCSP package, it just mentions AIN1, AIN2, and AIN3....
Hi,
I am facing an issue while flashing the code using an external debugger. I want to flash an LED blink code on the I/O shield " Raytac MDBT53V-P1M. " For this, I am using...
Latest 2.7.0 toolchain.
nrf5340DK board, light_bulb example.
I am using our own smartphone to perform up to AddNOC and ThreadNetworkSetup.
Then the control is transferred...
Hi, I would like to write a log to an SD card but I am completely unable to even connect to it using SPI in Zephyr/nRF Connect SDK. There seems to be some mismatch between...
I am working in NCS v2.7.0 for nRF52833 DevKits, and trying to set up a secure BLE connection to allow remote control of the device over GATT.
My devices are headless IOT...
Hi All, I have a 5340dk and it got bricked for no reason, last night I was able to flash and debug my program. But when I tried this morning, device is behaving unexpectedly...
Hello !
You have DTM test in nRF5_SDK_17.1.0 and in nRF Connect SDK.
I have used SDK test some years ago and it looks more simple if we compare it with new environment...
