I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi,
We have a nRF5340-DK board with the following setup:
b0 as the first stage immutable bootloader
MCUBoot as the second stage upgradable bootloader, which needs...
Hello, I have an issue with a project I'm working on with a nRF5340 Audio dev kit. I am using VSCode with the nRF Connect SDK plugin, and SDK version 2.6.1.
I need to have...
Hi,
We are working on nRF5340 with TF-M enabled and iOS application.
What we are observing is the peripheral device MTU TX and RX are configured to 512 bytes whereas the...
Hi I'm using nRF7002-DK kit and I noticed that the output voltage of a GPIO is 1.8 V instead of a 3.3 V. I have encountered a solution mentioned that we should apply these...
I’m working on an nRF52832-based project using the Nordic SDK (v3.5.99-ncs1-1) and MCUboot for OTA updates. I have a 512KB internal flash and 4MB external SPI flash (P25Q32H...
we are using SPI3 in nrf52840 with nrf SDK 16.0
we are using this as below
1. SPI3 init -polling mode
2. SPI3 unint
3. SPI3 init - DMA mode
4. SPI3 unint
5. SPI3...
Greetings,
Is the command toggle_dcdc_state supported in the radio_test sample when compiled for the nRF5340? ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples...
I started with the BLE provisioning sample (ncs\v2.7.0\nrf\samples\wifi\provisioning\ble) using nrf7002dk/nrf5340/cpuapp build target with sysbuild which works fine to provision...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
I am trying to use the `ram_report` tool and the results seem to have some issues:
1. The total size reported is much more that that reported when linking the zephyr.elf...
We are not using system off mode. since we not using external rtc. We are using internal Real Time counter in system on idle sleep (using ksleep).
In Basic led code , We...
We are building a Bluetooth remote using nRF52810 and nRF connect SDK v2.5.1
The remote have 20 buttons to be transmitted every 100mS, and we need several LED on / off commands...
I am trying to measure the battery voltage on my custom board which is based on the nRF52832 device. I am using nRF Connect SDK 2.7.0 in VS Code. The dts file for this custom...
Hi，
We had some trouble doing the certification of Tepec， Telec certification requires the RF power accuracy of ±3.8dB , while it is ±4dB in spec。Do you have any good advice
