Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I am trying to run the blinky Demo on the nRF52DK on VScode, the whole process is smoothly, but it can't work, the LED no any action. could you know anything I miss? many...
When I was making the upgrade package, I encountered a problem, and there was no problem in making only one upgrade package.
It is also possible to make protocol stacks...
Hi All,
Using VS code, nr52840dk,v2.6.0sdk，sid_end_device demo, No changes have been made
Firstly, add build config
Then click on Flash
Clicking VCOM0 has no logs...
Hello, I'm using the example "smp_client_ble," and I can't manage to remove the boot message.
Below is my .prj file:
My toolchain is: NRF Connect SDK V2.2.0
I am...
The chip I 'm using is the nRF52840, the sdk and toolchain versions are both 2.5.0, my code is here :
When I call spim3 peripheral with nrfx library, I add
CONFIG_NRFX_SPIM3...
Hello, hope to find you well. I'm a beginner involved in a project that's migrating from the old SDK to NRF Connect (VSCode). The project uses nrf_crypto.h and nrf_crypto_rng...
We recently purchased the module 453-00052R from Digi-Key and have successfully implemented it into our project. The design is complete, and we are now attempting to flash...
Hi,
I am trying Asset Tracker V2 application in my custom board and rechecking results with DK to ensure no hardware reasons are there. Using SIM supplied with DK and...
Hi Support Team
Our project need 8mA charge current, how to configure charge current of nPM1300 to 8mA？ Or could you provides us other nPM chip or solution that can meet...
Hi all,
I have a custom board running on nrf9161. I need to flash the custom board with the NRF9160-DK. But I am running into some issues. the development is at early stages...
Hi,
I'm trying to add a manufacturing specific attribute to the On/Off cluster.
To do this I have so far created a custom attribute list with ZB_ZCL_DECLARE_ON_OFF_ATTRIB_LIST_CUSTOM...
Hi NordicTeam
i am working with the Mesh Dimming server example out of the SDK MESH 5.0.0.
While investigation the Packet loss in my prevous ticket i was wondering if...
Hi,
Working with the NRF5340-nrf7002 and the W25Q16RV flash memory in our project.
Initially, I configured an 8MB( W25Q64RV) external flash without issues and tested...
I've been testing the FMDN locator tag sample application with a nRF52840 devkit and I would very much like to get an answer to the following questions:
1. Is it possible...
Hi, I'm having an issue with the bt_mesh_resume() function in my project based on Zephyr and Bluetooth Mesh. My code is trying to cycle the Mesh network on and off to save...
