Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi all,
maybe a dumb question, but here to listen any advice. I am using nus to receive data from a phone, packets are in chuncks of 256 bytes, which is the "most used"...
When I flash the card and run it, I encounter the screenshot I shared in the attachment. The error "Modem has crashed, reason 0xfff, PC:0x0" occurs. Can't I send messages...
Hi.
We are using nRF52833 (on BL653 module) where UART0 and UART1 are used for communication purposes (one with STM MUC and the other with quectel modem). Current solution...
I'm working on a personal project and have designed and printed a small prototype board containing an nrf52810, external antenna, couple of crystals, and a ws2812b onboard...
Hi,
We are developing a mesh network. Our requirement is the one device can connect to three other devices. Using one connection as a peripheral and up to two connections...
I am working on iOS pairing and bonding and connection and disconnection through UART.I am facing issue where pairing is initiated after that the device is getting automatically...
Hi,
We are experimenting with Distance Measurement feature a we observed 2 issues.
HW: Custom HW with: CR2032 coin cell -> joulescope -> 40 uF capacity in ceramic caps...
Hi all ,
I 'm experiencing issues with MQTT client connection on an nRF9160 board via LTE -M .
Some context : I 'm trying to connect to a MQTT broker via LTE -M (actually...
Hi , I am wondering if anyone with SPI expertise can answer this Q , I 'm using an nRF52840 with spi_transceive_dt()
In my devicetree I've configured SPIM on SPI3 to talk...
Hello,
I used the default sample from the nRF SDK with the same prj.conf file. I can flash it to the board successfully, but I'm seeing an error in the terminal. My toolchain...
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_freertos
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_rtc_freertos
I burned these...
I am using nRF52840 to interface my MPU6050 sensor via I2C , I build and flashed the program and there were no problem. But I can't see any clock signal on the default I2C...
I'm trying to build the zephyr/samples/net/sockets/http_client. I selected thingy91_nrf9160_ns for the board config and it builds and works fine. However when I enable
...
In my project, need an external sram with SPI interface to increase the sram volume.
I'm not sure if I can do it，please give an exsample in C language and some tips.
An...
