Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
I currently do some advertising tests with Nordic's nRF52840-DK and Zephyr. I have one board doing extended advertisements, one transmission every second. By means of...
Hi,
We are using nRF52820 right now and we would like to decrease the current of advertising, I have set the "init.config.ble_adv_slow_interval" to ''1024'' and the average...
ref. an earlier ticket,
I am using ncs 2.0.0 on a custom nRF52840 board
When enabling the CAF BLE state module, I get a build assert error due to
BUILD_ASSERT(!IS_ENABLED...
OpenThread daemon fails to run whenever using the nRF 52840 DK development board but works fine when using the nRF 52840 Dongle. I reinstalled it multiple times and started...
I would like to test he Wi-Fi Provisioning Service sample ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/wifi/provisioning/sample_description.html...
Hi guys,
for a current project, we need access to the local Zigbee binding table of the device (getting information about the binding of the current device).
I've spend...
Hi Nordic,
When I was using NRF52840 for FCC certification, the DTM 8dBm, 2Mbps sideband emission power exceeded the standard.
The antenna matching circuit is to use the...
Hello All,
I am using nrf9160 based custom board with external flash. I am trying to build an application with mcuboot, primary image in internal flash and secondary image...
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I am communicating with an Android device (SH-M05) as central.
There are times when I...
Hello,
We are developing a device that uses only NUS (Nordic UART Service) and DFU from the services. In this case, is it possible to implement Pair/Bonded with a client...
Hi,
I am currently trying to get the USB CDC ACM Example on the nRF52 DK to work using the SDK v14.1.0 . But for some reason I can only send/receive data using PuTTY but...
I found this post devzone.nordicsemi.com/.../zephyr-central-to-peripheral-communication , which was helpful to understand the overall structure of both central_uart and central_hr...
I'm trying to build the UART app with SES as per this example:
And I'm getting this error in SES:
Did I miss a step in the installation and setup somewhere?
Dear Support team
1) I find that there is a C9 in the nRF52840 reference circuitry for CKAA WLCSP which said that the C9 is not required for Fxx and later as the picture...
Hi,
I am using ppk2 to measure current on a custom board based on particle bsom (nrf52840). I am running ampere meter mode and I can measure some current, but values looks...
