Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I have AES ECB encryption working on the NRF5 system, but I cannot get it working on the Connect SDK.
I have found CONFIG_CRYPTO_NRF_ECB config, but this seems to require...
Hi!
I'm trying to run SPI slave on nRF5340 - doesn't work - project doesn't even build, the SPI master is running.
Can I see an example of NRFX SPI Slave for nRF5340?
Hi, I have several issues just to start off with. One is when I generate support information, it does its thing, and then stops, and I have no idea where the support information...
Hello,
I am looking for the detailed schematic of the debugger board which is packed along with the Thingy:53.
I need to understand the detail pin configuration for...
Hello there,
If I init a UARTE module (nrf_drv_uart_init) with e.g. Pin RX = 3 is it already enough to just disable the module (nrf_uarte_disable) so I can use the RX...
MCU: nRF52840
IDE: Keil uVision
SDK: 15.2.0
Board: Custom
Hello,
I realize there are a ton of threads about this, but none address the specific question I have...
Hello,
My board is powered by lithium-ion batteries.
It works from 3V to 2.1V. And It stop working at 2.1V.
After discharge, I re-charged battery. But It doesn't work...
I want to achieve reproducible builds on my development machine and a gitlab CI/CD server. So far the generated binary differs if I build locally (VS Code + NRFConnect SDK...
nRF5_SDK_17.1.0_ddde560
nrf52832
Cache overflow at baud rate 921600. I use the register to complete the serial port driver. I don't know how to use registers to implement...
To the kind attention of Nordic support team,
I'm testing a freertos project, with softdevice and radio notifications. A constant number of notifications is queued before...
Hi guys. I saw a previous post saying the LE Power control not supported.
For nRF Connect SDK v2 / nRF52 or nRF53, are there updates on LE Power control?
Since that...
Hi there,
I have just started the NCS Fundamental Course and I am stuck on Exercise 4 Lesson 1 and Lesson 2. There are two problems that I am facing.
1) If I use the nrf52832DK...
Hallo,
up to now I worked with nRF52840-DK 2.0.1. After compiling, flashing the board was quite comfortable by means of the JLINK drive, which automatically opens after...
Hi there,
This topic coul be part of a BLOG POST called OTA updates of a Nordic Device I think
Btw, my issue is this: Handle an OTA update of a Nordic Device, getting...
In my project, button ,charge state check and ACC sensor Interrupt pin, use GPIOTE; when The device is charging, keep this state one night,n ot unplugging the charger.when...
