Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Want to store the CONFIG_BOOT_SIGNATURE_KEY_FILE in the project space, not the ncs folders.
Looking for a method to define file location without using a absolute path. ...
I am using NCS v2 and VSCode extension on Windows 11.
I have two pieces of hardware I am testing with:
Adafruit nRF52840 Feather
Custom nRF52840 board
When I flash...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I would like to automate some unit tests with NCS. I tried running the native_posix qemu builds, however, this does not support the mac m1 architecture (maybe Linux only?...
I'm updating the NCS we are using from 2.0.2 to 2.1.0 in order to use the modem firmware 1.3.3 that was just released. I verified my build with NCS 2.0.0, 2.0.1 and 2.0.2...
Hello!
I use NRF Connect SDK 1.8.0, but peripherials are configured using nrfx library.
My task is to implement serial interface where I have PIN_TX and PIN_RX. I transmit...
Hello All,
I have few questions below:
- Does the ENABLE input disconnect the internal power systems completely, or does the circuit remain in some mode and nevertheless...
Hi Sir,
I am testing the NDT w/ example "nRF_DM" (NCS 2.0.0), there are two nRF52840-DK for this test. When two boards link success, the terminal starts to show the log...
Hello everyone
In the company I work for, we make a special kind of dongles which are able to connect to smartphones through BLE and transfer data.
I have 4 of these dongles...
Hi there,
I am working on a door lock project using nRF 52840 DKs and nRF5 SDK for Thread and Zigbee v4.2.0. we are having both ZigBee and BLE protocols in it. I started...
Hi everyone,
I'm trying to implement directed advertising on the BLE codeded PHY.
My setup of consists of two identical NRF5340 based custom boards, running FW based on...
Hi, nice to e-meet you. I want to use nRF52810 pin 25 (or other pins) to drive an external board, and through it to control the external board switch.
I set the pin to H0H1...
Hello,
I am currently working with pc-ble-driver-py and have observed write operations taking an exceedingly long time. Previous DevZone posts on this topic seem to be unresolved...
Hi,
Sorry to seek help again but I cant solve this issue
Steps
1 - nrfjprog -f nrf52 --eraseall
2 - nrfjprog -f nrf52 --program mbr.hex --sectorerase --verify
With...
