Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi, Here is what I have done so far:
Windows 10, installed Segger for ARM 5.68, using the Tool Chain Manager installed nRF Connect SDK v1.8.0 ( installed in folder C:\Nordic_Semi...
Good morning/afternoon/evening,
So I am fairly new to nRF system and wanted to know if there is a way to execute an interrupt when one of the buttons on the board is pressed...
Hi, I have a custom board built around a nRF9160. All GPIO (P0.xx) work. However, when I test with the at_client only AT+CGSN=1, AT+CGMI, AT+CGMM and AT+CGMR return with the...
Hi,
We are evaluating the possibility to connect our nRF52840 to another BLE device but we are facing issues with UUID Nordic handling strategy.
Quickly:
We have...
Hello,
I applied for a SUPL license for two weeks, but was denied.
I repeated logout/login, but it was the same.
please help and check.
Thanks,
SY Kang.
Hi,
as follow is nRF5 SDK code to create a timer ms.
how to create a timer ms on nRF Connect SDK ?
APP_TIMER_DEF(m_timer_speed_1ms); int timer_lms=0;
static void...
Hi,
we have an odd issue on ~ 50% of our in-house boards here. We're using the internal RC as a low frequency clock, and then enable one RTC. No softdevice or anything....
i am using nrf52840 USB dongle and the segger J_LINK EDU mini for debugging when i use bulid and run it works, and if i remove the donle and reinsert it then ts not working...
Hi,
I was using nRF command line tools 10.14.0 before. i try to update to 10.15.1 but fail with below log.
Do you have any comment for us to overcome this issue? ...
Using NRF Connect for Desktop V3.9.1 for Windows. We flash custom boards with J Link EDU 9.4 version. Since update to Programmer v2.0.1 it will not detect the J Link. Any...
Hi,
ncs1.8.0\zephyr\samples\bluetooth\periodic_adv\
ncs1.8.0\zephyr\samples\bluetooth\periodic_sync\
periodic_adv and periodic_sync
how to change to use Zephyr controller...
Hi,
I have a nRF5340 with USB DFU support which uses MCUBoot for upgrades. The current build (app_version_1) on the nRF has 0x4000 as the size of the settings_storage. The...
Hi,
Developing by NCS SDK, We found it will take 20 minutes by using mcumgr(on MacBook-pro) to BLE OTA 178KB image to nRF52840 Product Board's external SPI FLASH. it success...
The following is my set up:
platform: windows 11,
editor: visual studio code with nRF connect
SDK: nRF connect SDK v1.8.0
toolchain: nRF connect SDK v1.8.0 toolchain...
