Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi,
We are using Nrf51 with SDK nRF5_SDK_12.3.0_d7731ad
We based a UART bridge on the BLE_APP_UART example
The UART connectivity is Rx/ x only (RX_PIN_NUMBER 0; TX_PIN_NUMBER...
Hi,
we've noticed that after performing an OTA DFU, the Bluetooth Address of the device changes as follows: new_address = old_address - 1
Example: Address before OTA DFU...
Hi there,
I am a beginner to the nRF series and I had the following question.
For a battery powered system, is it better to run the nRF52840 at a lower voltage such...
Hello,
i'm trying to program on 51422. The BLE signal,which runs well on 51DK, doesn't trigger any signal on my own PCB. i've successfully light the LED on my PCB. i think...
Hi,
I'm using nRF52832 and I'm trying to switch from SDK15.0 to SDK 15.2. While I've been able to install micro-ecc library in SDK15.0 and use OTA DFU, somehow I'm stuck...
Hello.
I want to integrate UART and SPI ,I am using SDK15.2. The problem here is i am not able to add app_uart.h to main.c(spi).
My question here is how to add it to main...
My working platform is nRF52-DK, and I want to execute DFU firmware upgrade
1. How to create a Bootloader Image? Which Source-Code of SDK_15_2 is used to build the bootloader...
The RTC documentation states that the LFCLK source needs to be explicitly started by the software.
Is this step necessary when using the SoftDevice? As far as I know, the...
I'm not sure about how does the ble_app_att_mtu_throuthput example works exactly, i supose the throughput test runs as follows:
1 tester defines a service 'populated' with...
Dear all ,
Working with nRF52832 (currently without SoftDevice), and there some issues regarding the project current consumption that we need to understand:
1) In the...
Hi,
I am having a trouble trying to make a custom service from SDK 15.0 ble peripheral template example. I have followed the tutorial from : https://devzone.nordicsemi.com...
Hi i'm a newbie, Got Thingy:52 (Keil and J-link) and want to develop HOGP keyboard application. Where can I find Tutorial or example ?
Is there a step by step guide on how...
Hello everyone, I'm using nRF52 kit which has got only one UART module, i'm also using the log driver(which uses UART, typing stuff into a virtual terminal using NRF_LOG_INFO...
hello everyone, I need a low power product, so I am using nrf52840. There is a problem now, When I add "app_timer_init()"(I never change the code in this method) in my code...
