first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi all,
I am evaluating ANT+ features in nRF52 DK board and I am using nRF5_SDK_17.1.0_ddde560 SDK.
I need to implement ANT+ Bicycle light profile (LGT) in my device....
Hi.
I'm developing a ble module now.
I have a question about time out, interval among BLE init Advertising.
As shown in the picture below, time out (in units of 10ms...
Setup:
nrf52840DK (Zigbee Cordinator based on Zigbee Coordinator sample)
nrf52840DK (ZED)
NCS v2.4.1
Hi,
I am working on Tunneling cluster handling as that one...
Development environment: ncs 2.6.0.
my application need BLE-DFU, so i added multi-image support to my project.
the pm_static.yml is the typical default system configuration...
Hello,
I am working on a SWD flasher for nRF52 chips. I try to perform basic commands like flashing a firmware or reading flash content. I wanted to use FICR informations...
I am using NCS V2.6.0 and using zephyr there is no examples to measure battery level using saadc we can measure the battery level right? I used LEDs to indicate battery level...
Hi, I'am working on a design with nRF7002 and I need add WiFi antenna NN03-320 from Ignion and when check the datasheet of the builder of the antenna I see that the pin 4...
Hi there,
Is there any drawback or limitation in the S140 SoftDevice (v7.3.0) if a connection (as master) stays open for a very long time (weeks)? I mean, there could be...
Hi,
I use our customer board that enable the i2s to the DAC to speaker. However, i only verify the play a wav file directly that seems work normally but our target is playing...
which sample is best for me to verify the central/peripheral communication using nRF52833 for nRF52 serial.
I have two nRF52833 DK board, I need the board2board communication...
use NRF52832 do a ble hid keyboard,
when do the keyboard function test need connect the keyboard to computer or laptop.
only when the connection it's done, then can run...
I used nRF52840 board with SDK 17_1_0 ,
For FCC Certificate We used Radio Test Example,
using start_channel 40 & start_tx_carrier we change the frequency and we are able...
I am using nrf52832, SDK17
When I am setting up a timer with no applicable interrupt handler it fails so
This is how initialize the timer
when I do define the handler...
Hello community,
I am trying to develop a custom bluetooth HCI_USB code for the BL5340PA BLE controller board. The Liard Connectivity's(now Ezurio) BL5340PA : https://www...
