Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Cause of the issue Earlier, when I were producing products ( around 600 units with 2025.9 ), about 30% of the chips had difficulty connecting. Later, it was found that the...
Hi,
I am implementing a custom bootloader on an nRF52840. The firmware update is downloaded while the main application is running. The flow is as follows:
The application...
Hello I'm working on a nRF9151 DK using nRF Connect plugin for VC.
I was able to program and run my without any problem... but then suddenly the flash process stopped to...
Hello.
I use the bare metal SDK and I would like to generate a GRTC interrupt every 250ms to wakeup my system.
Which resources does the zephyr is already using (GRTC_x_IRQn...
Hi,
I’m using an nRF52810 with nRF Connect SDK v2.5.1. I want to read the internal temperature sensor. I started from the LBS sample and added NSMS to report the temperature...
I'm working on the firmware for a custom board built around the nRF9151 SiP. The firmware is built against the nrf9151dk/nrf9151/ns board target included in zephyr, with an...
HI
I am using nRF54L15 PDK with NCS 3.0.0. In my code, I am using NVS to store data on the MX25R64 flash on the PDK. The initialization code is as follows:
struct flash_pages_info...
Hello, I am currently working on a PDM microphone project using nRF52840 and Zephyr RTOS. I've been testing the official Zephyr sample (located at dmicncs/v2.9.0/zephyr/samples...
I have three questions regarding the electrical parameters of the NRF9151 chip:
For a GPIO configured as output: What is the maximum source current per pin when driving...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2. Because our terminal device 1 does not support using ble-FOTA, I used another terminal device...
Hi,
We have a custom nRF9160 board with chip antennas for LTE and GNSS. They are Ignion antennas with matching circuits customised to our board dimensions. We also use...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
I’m testing low-power behavior on an nRF52811 device.
When SoftDevice is not enabled , calling nrf_pwr_mgmt_run() gives me a stable ~5 µA average with no visible...
