Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hello,
I'm currently trying to integrate the Android-nRF-Mesh-Library in our App.
Identifying works fine but when the library tries to send the public keys to the node...
I started to test with NCS 3.0.0. The first surprising topic I found was, that the nRF Connect for Desktop - Toolchain Manager (v1.6.0) doesn't support NCS 3.0.0 other by...
Hello,
Is there documentation, or an example, explaining how to avoid accessing peripherals owned by the SoftDevice controller in an Application?
I found this:
docs...
I'm using nrf52840 dongle. followed setup based on
https://docs.nordicsemi.com/bundle/nrfutil_ble_sniffer_pdf/resource/nRF_Sniffer_BLE_UG_v4.0.0.pdf
https://www.youtube...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
Setup: NCS v2.8.0 nRF52840
Hi,
I would like to ask about the implementation of Zephyr's SAADC driver (` adc_nrfx_saadc.c `).
In the project I'm working on, I need to...
Hello,
already found a description in the Tech Docs, how to bring the external memory into deep sleep on QSPI interface: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hi,
The Thingy 91 X uses a shared antenna for BLE and Wi-Fi. I can see from the Hardware Guide and the schematics that there are several hardware connections between the...
Hi,
I am working on implementing the BME680 sensor with the nRF5340DK using the I2C protocol. I have successfully obtained the slave device address and the sensor address...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
Hi everyone!
My name is Natalia, and I’m just starting to work with Nordic. This is my first design, and I’m trying to connect the nRF7002 module to the nRF52840 microcontroller...
As part of a university project I am trying to read an analog signal and transmit it at the maximum data rate over ESB. But I cant seem to get above 1700kbps without any of...
In https://docs.nordicsemi.com/bundle/ps_nrf54L15/page/uicr.html#register.BOOTCONF, I can seee that it is possible to apply Read protection to the first x kB of the RRAM by...
