We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I'm using an nRF52840 microcontroller on an electronic board to read from and write to an S25FL064 flash memory chip. I'm currently using the nRF5 SDK . Before I could read...
I am trying out the Nordic Bluetooth ESL sample example code from the link [ Getting started with bluetooth-esl-and-periodic-advertising-with-responses-pawr ]
Downloaded...
I understand from many posts that the DTS file is ignored when in multi-image (mcuboot enabled) I need to change the partitions to reduce the bootloader from 48K to 32K &...
Hello Nordic Support Team,
I’m currently experiencing issues connecting to my nRF52833 hardware. The device was previously working without problems, but now I’m unable to...
Hello, I am currently developing with NRF52840 and NRF7002 chips. I am running a custom version of the wifi scan sample, using the baremetal library and custom shim file....
Hello,
I wanted to check if it’s possible to use the BLE Mesh light code with other BLE Mesh apps such as ST BLE Mesh, Bluetooth Mesh, or AMCCOM Mesh.
I have tested it...
I am taking some courses from DevAcademy to learn about Zephyr.
I do have some zephyr supported board(s) for the hands-on exercises, but they are STM32 based, not nRF
...
I note that calling:
mpsl_lib_init causes the POWER . INTENSET to be cleared (including the USB interrupts and POF WARN).
My device uses the USB stack, as such, calling...
Hi,
I'm trying to combine Wifi and BLE frequency test on nRF7002 DK. I started with radio_test example on nRF SDK 2.9.1 and toolchain 3.0.2.
I have added CONFIG_NRF70_RADIO_TEST_COMBO...
Hi.
When I made a application with mcuboot on nRF54L15DK.
In order to reduce power consumption, I want to disable serial log(UART).
I added these configuration in the...
Hello,
We have successfully connected a team device and are receiving telemetry from nRF Cloud via MQTT. We subscribe to prod/{team_id}/m/# and receive all team messages...
Hi there.
i start working with nrf54H20 with the hello world example but i encounter to a problem while compiling the example and i dont know what is the reason ?
the...
Hello and thank you for your help
I am working with the 9151 Rev3 and I attempted to update the IMEI with a valid one provided to us by Nordic
But the following error...
Describe the bug I would like to inquire about an issue where when my PD (Peripheral Device) continuously sends commands without interruption, the PD encounters this error...
