Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
In the SDK 17.1.0 release note (downloaded from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK/Download?lang=en#infotabs ), the verification GCC compiler...
I'm trying to create a Zephyr Shell command where I can write a certificate to the modem. Putting the certificate in the command line doesn't work, so I was going to use the...
Hi
I'm using nRF52805 to realize the DFU function using the buttonless_dfu example project. I follow the instruction of this and use commands in this discussion .
After...
Hi I have an question about use ZB_ZCL_DECLARE_POWER_CONFIG_ATTRIB_LIST macro in case when only one battery used.
I'm trying to declare Power Configuration like this
...
Hi. I don't believe this question would be strictly be considered a duplicate. I have seen posts discussing the same issue I'm having, but resolutions don't appear to solve...
In order to use this application in nRF Connect for Desktop, I have just purchased an nRF52-DK. As I'm using macOS, I believe that I'm affected by the 64 byte limit and need...
Hi,
I am trying to interface WM8960 CODEC with nRF52832 using (I2S and I2C) .
Problem I am having is with TWI scanner and also sending data to the know i2c address . have...
SES 5.44
nRF52840-DK
GNU Arm Embedded Toolchain: 9 2020-q2-update from here
S140: 7.2.0
Project is C code only
Project Setup:
Linker Script File (copy from...
Hello,
I am a research assistant at the Norwegian University of Science and Technology. We have in the past been using the micro:bit v1 for our practical labs which purpose...
Hi, When I hook the nRF5340-DK board to my PC, the SEGGER J-Link OB debug chip bothers me popping up a GUI that exposes the board as a USB mass storage device. How to get...
I'm using Android DFU library 1.11.1 and occasionally I see "E/DfuBaseService: Connection state change error: 133 newState: 0" errors. It appears they happen when the initial...
When using nRF Connect SDK v1.6.1, a BLE peripheral that supports 2 simultaneous connections could be created by including these lines in prj.conf. These lines set the Link...
Hi,
this is kind of continuation of my previous ticket . After solving it the last time I thought that I don't need wait_for_flash_ready() function as it caused some problems...
I just buy nRF5340.
I install nRF Connect in my PC.
and install bluetooth app.
I just select my pdk.
log show
INFO Connected to device with serial number: 000960119975...
