We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Dear support,
I am using nRF52840DK board (PCA10056) with SDK version: 17.0.2 version. I am trying out the USB CDC_ACM sample application from the path: <SDK_PATH>/examples...
I am using nrf connect sdk 1.7.99 with nrf5340dk. When building the ncs/zephyr/samples/net/socket/echo_server sample with the following command:
west build -b nrf5340dk_nrf5340_cpuapp...
I want to use Mbedtls for secure boot so I got to know that I should define CONFIG_BOOT_MBEDTLS
1.but when use that I am getting error as,
error: BOOT_USE_MBEDTLS (defined...
I'm using s132.
I'm using the app timer with the app scheduler.
I'm running a simple loop and constantly scheduling the timer in the timer callback.
The callback works...
Dear forum,
I want to achive low energy consumption for a BM833 (with crystal).
From the following thread, I could deduct, that running the softdevice, an average of 300...
Hi,
OS: Windows 10
SW used is Segger IDE, nrfCOnnect for desktop to program HW used is nRF 52480 dongle PCA10059
I am starting using nRF 52480 USB dongle, I need to...
I am working with nrf52840DK, SDK v17.1.0.
I compiled and downloaded the open bootloader project to the DK using SES (No errors and verification says OK). According to...
Hi,
We wanted to add an additional flash section to the linker.cmd file located in the zephyr folder of the project folder. However, when we make changes to the memory section...
We have a situation where the network core of the nRF5340 has been given control of Port 0/GPIO pin X (GPIO0->PIN_CFG[X].MCUSEL = 1 on the application core). The network core...
I have 2 dongles that I've somehow managed to brick (I don't remember the details on how i did it). One of them goes into DFU bootloader mode when I plug it in but shows up...
Hi,
I am modifying the code to asset_tracker_v2 on Thingy91 to send data to my own server instead of Azure / AWS / Nordic Cloud. I am getting error code -35 (EDEADLK) when...
The discussion in https://devzone.nordicsemi.com/f/nordic-q-a/79364/maximum-number-of-bytes-that-can-be-used-in-beacon-advertising suggests that we should be able to populate...
As far as I understand I should be able to use the nrfutil (6.1.x) on a Rpi 4B to update any of the nordic semi devices nrf5x supporting bluetooth (i my case nrf5340) Will...
I am new on Bluetooth. Currently I am playing with BL5340 development board. I need a firmware to test Bluetooth data transmission latency between two BL5340 modules. Could...
