Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Thanks in advance for the help.
I connected my 9160DK (V1.0.1), loaded Asset Tracker V2, etc., and seem to be connected to nrfCloud fine.
I don't seem to ever receive...
Hello all,
I am trying to on implement a custom 802.15.4 implementation (not thread nor zigbee) from the nrfxlib 802.15.4 radio driver in NCS. The goal is to run it in...
Hi, I have this weird issue with the USB behaviour of some of our pre-production units.
2 boards with USB came out of the oven and their USB was working fine. I was able...
HI Devzone
currently my customer would like to get SRAM execution permission in their porject.
we found a config marco to set the SRAM permission " CONFIG_SRAM _REGION_PERMISSIONS...
HI,
i using 52840DK SDK17.2 s140 10056 test NFC pairing.
ble_central\experimental\ble_nfc_pairing_reference_c 10056 s140 ble_peripheral\experimental\ble_nfc_pairing_reference...
I am using
MF V1.3
NCS V1.6.0
nRF9160Dk V0.15.0
Project: AGPS Sample
If i set the Interval in the gps_config structure to any number under 240 and run the sample...
Hi,
We are working on nrf52840 in that we have some doubt how to test the radio tx and rx in datasheet you have mentioned
Active mode Tx Current - 4.8mA and 0dbm ...
Upgraded from v16.0.0 to v17.1.0 and have a truncation issue. It only occurs after the first send. Reverted back to v16.0.0 and all ok.
No other code change other than the...
I've searched around, but i couldn't find anything about how to use DMA with SPI master on a nRF5340 (and zephyr doesn't support DMA on nRF5340 right?). Can someone point...
Hi,
I'm using ble_app_uart to test AT.
When I sending a buffer
reset_buff[10]="AT+RESET\r\n";
RTT log showing an error
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at...
Hi all,
I'm currently trying to interface an nRF52832 with an external Flash chip via SPI
I have tried with both NAND and NOR types, specifically the MT29F2G01 from Micron...
I am trying to develop CAN communication using nRF52 dev kit based on nRF52832 (PCA10040) and a MIKROE CAN SPI click 3.3V board . This board has an mcp2515 stand alone CAN...
Hello,
I had RTT configured as the logging backend and it was working fine. When I enabled the SHELL on RTT, the log output stopped. Maybe more specifically, printk() output...
Hello there,
I'm trying to downgrade nRF Programmer from v2.0.0 to v1.4.11 as it is not possible anymore to select a Segger debugger as target device in the newer version...
