Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
i have a custom board with an nrf52840, i use a J-link programmer to flash the chip with the nrf connector programmer app.
I am able to read the memory and erase the chip...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.5.1
Zephyr version: 2.4.99
BLE controller...
Hi,
I want to run the Thread MQTT-SN Publisher and Subscriber example using the nrf52840 DK and the nrf52840 Dongle I have on hand.
I was able to sucessfully build and...
Hi, I'm trying to use BLE/Thread Multiprotocol for BLE RSSI scanning and send values using Thread, is it possible to use BLE and Thread(FTD) concurrently with out time-slice...
Hi all, Using SDK 17.0.2, on a Laird BL653. I've been messing with creating variable PWM sequences and found an issue where a 100%->0% duty cycle transition does not occur...
I once used nRF Sniffer with my nRF51822 module. I see that everything has updated since - Wireshark, Sniffer plugin (now is Python 3.4+), Sniffer firmware. As I can see,...
Hi all, i don't have any issues I am just now using the nRF Connect power profiler after a ~4 month break. WOW, the major update is absolutely phenomenal. The graph is very...
Dear Nordic DevZone community,
we modified the LwM2M client example to fit our application in a LTE-M network. Now we are trying to get GPS to work while still being able...
Hi.
I'm using nrf52832 with SDK-17, and the ESB example (esb_tx and esb_rx)
I'm not much experience in nrf development recently I have a project related to ESB to transmit...
Hello,
In nRF52832, we use nRF Connect to read the board, save the program data into a hex file, and send the file to other developers. They can use nRF Connect to write...
I am using sniffer v3.1. I have installed the sniffer code on a nRF52840 dongle (PCA100059). When I insert this into the PC with windows 8.1 it appears as "nRF Sniffer for...
Hello,
In our product, the nRF9160 is configured to use LTE CAT-M1 and we are measuring the signal quality thorugh the AT+CESQ command.
After begin registered on the...
Hi: I have write a spi slave, and write a spi master on STM32, It can receive data from STM32,But I have no time to prepare the response data.
as the code below, I can receive...
I checked the SPI communication using the NRF52832 development board.
Based on the firmware of the previously developed NRF52810 product, the SPI operation code is applied...
