Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I am trying to read data from a chip over SPI.
The implementation of the SPI comms is not ideal as they require a new CS/SS line toggle on every byte. I cannot do a bulk...
I hope that someone can show a clear example of this. I surprised that it isn't in the SDK examples. Basically, it is necessary to stop the BLE SD, in most low-power examples...
Hi,
I am having a problem where the client is unable to receive notification from a peripheral after the softdevice in the peripheral returns 0x3002 after a disconnect....
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of openThread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure...
I am Rattana. I have some project for Bluetooth communicate with mobile phone. Then I will use BC805M(nRF52805).Nomally I connect my MCU with HC06 and I use MCU because I...
Hello I'm now trying to implement the IOS Phones (Central) - Device (Peripheral) liver UART using Multiple Connection - Nordic Uart Service. Devices tried to send a UART signal...
Hi,
We are following the project CHIP and planning on design a matter device with our existing hardware platform. The below are some questions about it:
1. Our platform...
Dear Nordic Bluetooth Experts,
My project is quite simple: A BT Mesh device (generic level server model) powered by a Nordic nRF53832 and an Android app that is used to...
Hi Everyone,
This new way of doing firmware seems to have taken such a turn from what I've been doing for the past 20 years that I don't know where to begin. All I'm trying...
Hello,
I am using android nrf mesh app as a base app and using the latest nrf mesh library version.
I am taking provisioning trails on inline on-off controller.
While...
Hi,
I have used "write_handler(p_ble_evt->evt.gap_evt.conn_handle, p_rtc_service, p_evt_write->data[0]);" to send data to nrf52832 from nrfconnect mobile app but iam able...
Hello,
For our application, we need to form a Zigbee distributed network and not a Zigbee centralized network. That means that routers need to be able to form a new network...
Hi , I have a problem when I wanted to combine the two examples twi scanner and usbd ble uart together although they work correctly individually I have a MAX30105 sensor which...
Hi all
We're developing an application for nrf9160 with zephyr-sdk v2.4.99-ncs2 and nrf-sdk v1.5.1.
In our project we are required to use a Library which forces us to...
Hello
I want to sampling two analog.. with different configuration and handler.
so I set two channels like this.
and then I call only one sample function like...
