Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello, I'm trying to integrate an SPI slave into ble_app_beacon example. Power consumption of ble_app_beacon between advertising is up to 10 uA. But if I write a byte over...
Hello
I am modifying the example of mpu6050 of sdk v14 in sdk v17.
After build, it is printed that there is no path to the file as shown in the image below.
(The...
Hello We recently went to a test facility SGS, in San Diego, with our nrf9160 device trying to get a pre-cert scanning completed to find out if there are changes needed before...
Using SDK 15.3 and S132.
I'm having similar behavior to the thread below:
https://devzone.nordicsemi.com/f/nordic-q-a/12066/gap-disconnect-stops-app-timer
After disconnecting...
hi ...
how to update the advertisement packet .. I have seen many post regarding this ,I am not getting clear , anyone can share me the piece of code which will help me
I am trying to repeat the example in the tutorial: using board: nrf9160dk_nrf9160.
nRF Connect SDK Tutorial - Part 3 | NCS v1.3.0 --> 1.2 Walkthrough for BME280 - but gives...
Hello,
Our setup:
-nRF9160
- Zephyr OS
- Segger Embedded Studio for Arm (Nordic Edition)
- SDK v1.3
Questions
1) which are the differences between Zephyr functions...
I'm designing a product around the nRF52840 (PAN1780 module), and using the PWM to drive a piezo sounder (using 2 pins as Hbridge). When I start using BLE functions, I get...
Hey, Yesterday we decided to update SDK to 17.0.2. After this change our FreeRTOS stopped working. We started investigating where is the problem and we found that when vPortSetupTimerInterrupt...
Dear all,
I'm currently using nrf52840DK with SDK 17.00 and s140 softdevice. I'm trying to syncronize the dispatch of my data with connection interval (set to 7.5 ms). I...
Using: Windows 10, nRF Connect v3.5.0, SES v4.52, ncs v1.3.0, zephyr v2.3.0
I have a custom board based on the Thingy91 and the Asset Tracker application. There is also...
Hi,
In the new AzureIotHub library, subsys\net\lib\azure_iot_hub\src\azure_iot_hub.c
the logic for handling connection conditions in mqtt_evt_handler requires more error...
How is CRYPTOCELL_IRQHandler linked in a project using CC310? I have built ble_app_interactive and it links to the library routine. However I need to develop my own application...
The current state of my thingy 91 is it blinks blue and then red. nrf connect reports that it has not been provisionized or something similar.
The included sim card is registered...
This is the third time attempting to install nRF Connect SDK on my Linux box at home, and have failed at the same place every time. I followed all the instructions while using...
