Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hai ,
In my application i should connect parallel connection and peripheral and central part connections simultaneously.
for this i developed from hrs_relay example .in...
Hello,
I'm trying to program a nRF52840 Dongle with the thread MTD client example by using nRF Connect but I get an error saying I need to add a SoftDevice. I thought...
Hello, I am new to NRF52. I have setup a project under Embitz ide. I can compile GPIO toggle code and program the the code. However when I try an transmit example github.com...
I have 100 samples of string data (Ex: AABBCCDDEEFF:1592636399:1592636399 ) . I am using the flash_fds module. Also, I want to read the read all the samples at once. I am...
Hi,
I am developing the 'buttonless dfu' to the 'hrs freertos' using the SDK v15.3.0.
However, after I compiled the modified code and loaded to the target broad, I got...
Hi
In ble_stack_init(), err_code = softdevice_enable(&ble_enable_params); err_code = sd_ble_enable(p_ble_enable_params, &app_ram_base); err_code is 4.
I use nrf51822 in...
Hi,
I got a nrf5340 pdk, and I download demo Peripheral_Heart_Rate into board, load peripheral_hr.hex into app_core and load hci_open_amp.hex into net_core. it running ok...
Hello. I have one multirole device (device A) and three peripherals (devices B, C, D). Device A connects to devices B, C, and D as a central role, and connects to the phone...
Hi,
I am developing a product using nRF52833 . (S113, SDK 16, IAR8)
I am developing based on the usbd_ble_uart sample.
I use ble, spi, twi, ppi, saadc.
and, I use...
Hi,
On page 420 of the nRF52811 datasheet (v1.0) it states that pin 14 (P0.18) can be either 1) Digital I/O or 2) Single wire output (SWO). The SWO is not mentioned on any...
Hello, In our project the nRF52 resets randomly
we use the NRF52832 with softdevice S332. On the application space we run a FreeRTOS application with 2 tasks. We want to...
Hi,
I am trying to determine whether or not to use a watchdog timer in our firmware. The device is and IoT device, making sensor readings and entering sleep mode for a while...
Hi all,
i am trying to merge ble_app_peripheral example with twi_scanner. So i created twi_ad7147.h and twi_ad7147.c with the twi configurations.
But i am getting this...
Hi All,
I am working on a custom board using the BMD-340 from RIGADO, and I am hoping to be able to see all the logs on the RTT viewer.
setup -> SDK 16.00, J-ling programmer...
