Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hello,
I got TCP Server example working on nRF52DK with Raspberry Pi.
I set everything up and can ping global addresses of DK on all interfaces (wlan0, eth0 and bt0) from...
Hello,
I am using NRF52832, SDK v15.1.0.
For advertising on single channel, I added " p_advertising->adv_params.channel_mask[4] = 03; " in ble_advertising_start() ,...
SEGGER Embedded Studio 3.12
nRF52 SDK 15.0.0
In order to generate peripheral driver library files，how to create library in project(have .c&.h file in this project).Only...
Hi,
SDK documentation says "You cannot write to UICR.BOOTLOADERADDR when using the default J-Link target driver in IAR". Some threads suggested it is only nRF51 issue, but...
Hi!!
Now I am using sdk 14.0.0 / example / peripheral / spi / pca 10040 / blank / arm5_no_packs /
I am sending commands to ads 1192 with nRF 52832 DK as master and after...
I had an issue on using HID to control the media in Android. It worked fine at the first connection, I could play , pause and change the song on phone. But it couldn't control...
Hi I would like to confirm which NRF51822 models are the 0.35mm thin WLSCP package. I checked Avnet distributor and they say that NRF51822-CTAC-R7 is 0.35mm but the package...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
I need to make an android custom app (with UART functionality) so that only...
I'm trying to get a third party demo application working and I seem to be having an issue with the nrfx_spi_xfer function getting stuck waiting for the NRF_SPI_EVENT_READY...
Hi everyone,
I'm learning about proggram the nRF52840 dongle and I tried to code an interruption. Press the SW2 to turn on a LED
So, looking at this code, where did...
I am trying to make the nRF24LE1 as a sensor node. So I want to configure it to work as a receiver/transmitter and simultaneously use the ADC and UART. But the moment I added...
Hi all,
I'm using nrf51822 and ble_app_multirole_lesc example on SDK 12.3.
When I connect with "nrf connect" Android application for the first time, the bind is established...
Greetings. Finally ordered some NRF52832 board from HOLY IOT and spend few weeks trying to handle with them.
So, all about setup:
SDK: 15 (15.0.0_a53641a) @ Windows 7...
Hello, I have just started evaluating SoC nRF52832 and have built a custom board based on recommended diagram from the datasheet chapter 53.3. Actually, the board diagram...
Config
Using NRF52810 on a custom PCB with 32kHz + 32MHz crystals, very close to the reference schematic
S112 with SDK 14.2.0 in SEGGER Embedded Studio V3.30
A button...
