Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
Am using nrf52832 for my BLE project with SDK 15.02. I found sometimes device is not showing after disconnect, I have to reset the device manually to show the MAC...
I'm trying to update my project to use the latest S110 softdevice release. The trouble is that I have written many of my own hardware abstraction layers and they are conflicting...
Hello,
I am trying to program a nRF51 chip with a dev kit. When I install the base nRFGo Studio, it is able to detect the board but it won't read the chip because it is...
Hi,
I am experiencing an interesting case ( I am not sure if this is a problem indeed).
I have been trying to develop code for ISP1507 (nRF52832 PC10040 based) on two...
Hi ,
I have tried to test the current consumption on NRF52840-DK (PCA10056).
DCDC is enabled.
RTC is running.
No BLE is advertising.
The DK is powered via USB. ...
hi，all
i got the nrf52832 dk and run the ble_app_uart example ,
but i found nothing output in jlink rtt viewer after called the NRF_LOG_INFO("UART Start!") ,
so could...
Hi.
I did the secure bootloader DFU. I attained step 8 in document .
I instal softdevice and secure bootloader to flash nRF52832. After make the ble_app_buttonless_dfu...
Routing the DCC pin on the nRF52832 with the chip scale package is pretty tough. The bump is surrounded on all sides by other bumps, so I don't have room for a via in the...
Hello,
I'm using nRF Connect V2.6.1 on Windows 10, I launch " Bluetooth Low Energy V2.2.0 " that uses PCA10059 Dongle as central.
Also, I have developed a peripheral application...
There are 12 LEDs which are connected using shift register HC595 ,the module used is nrf51822(bluetooth module). I want the LEDs to go off after 3 seconds interval. My code...
Hi there,
We are having issues with our boards that uses nrf52832 chip. Our first built had this chip and everything was working fine. We built a second batch and all boards...
Hi,
In nRF52832 datasheet I found that it is having internal oscillators, like 32.768Khz RC oscillator and 64MHz RC oscillator. If it is having internal oscillators what...
Hello
Most of the time we shall use the BT TX 0dBm. In special cases when we want to increase the communication distance we may select the 8dBm mode.
For RF type approval...
I am implementing long read with authorization in the server (peripheral). I have a characteristic with vlen = 1 and maxlen = 300. ATT_MTU = 23.
gatts_attr_md.vlen = true;...
