Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
It seems to be a bug in hal_device_reset() when using S132.
On line 8 above the function sd_power_gpregret_set() is called with the wrong arguments. The first arguments...
can I use an nRF52840 based BLE gateway? Backhaul would be either 10/100 Ethernet (via Wiznet or Microchip controller chip) or a cellular module. Is the clock speed sufficient...
I am unable to get 6 notifications per connection event. I am connecting two nrf32832's, one as a central, one as a peripheral. To make this as simple as possible, I limited...
Hi
We are able to provision several mesh-servers.
The log on the RTT-Viewer of the client looks normal:
0> <t: 915394>, mesh.c, 178, Local provisioning link established...
I am working with the peripheral/flash_fds in SDK14. I need to adapt it to use RTT instead of uart
I have made the obvious changes to switch from uart to RTT, eg substituting...
Hi everybody,
I'm trying to use the example ble_app_hrs with s110 on the PCA10001 Board and the ble_app_hrs_c with s120 also on an other PCA10001.
I changed some led flag...
I have already explored how to fix the related problem in the DevZone. I think the firmware of the ATSAM3U2CA-AU is erased. Here, I have two problems:
1, How can I get the...
Hi,
According to the code in PCA10059.h:
#define RX_PIN_NUMBER 11 #define TX_PIN_NUMBER 9
I would like to know what pins are related to number 9 and 11 in this schematic...
Hello,everyone.
If you have some suggestions,and you leave them, I would appreciate it very much.
I designed a pcb base on nRF51822. It can only be searched by mobile...
Dear Nordic support,
I am working on a device based on the FreeRTOS heart rate example and I am having difficulties with the BLE connection when connecting to iPhone X...
Hi, I want to reduce current my module.
I used SDK15.0.0ver, nRF52832
I have 2 questions.
1. I used app_uart_close();
But My module was reset again.
2. I want to...
hi...
i want to check my data for every minute , so i set the timer for one minute.
but its not working ....... how to do?
i have set the timer like below
i am finding...
Hello nordic team, I have a question regarding BLE Mesh and Uart0:
The InfoCenter is saying that Uart0 is blocked when using the serial Support. I don't wan't to use the...
